After the rose seeds have soaked overnight, rinse them in a strainer and place them into the blender with at least a cup of plain purified water (making sure all seeds are covered), and turn it on for a few minutes. It usually doesn't chop up the seeds, but rather, it will clean off the pulp remaining from the rose hip, which would otherwise mold if left on the rose seed. You may see a few seeds chopped up, but those usually aren't viable anyway. Flush the rose seeds again through a strainer using fresh purified water.
Rose propagating methods have changed over the years, from the simple own-root varieties of the Victorian era, and progressing to the budded hybrids of the 20th century with its many options of exotic understock such as Rosa multiflora, Dr. Huey, Manettii, and Fortuniana. Now, rumor has it that many of the modern hybridizers and commercial growers are interested in returning to the simplicity of yore. Today's commercial rose growers are finding that budded roses are just too labor-intensive and expensive to produce. Because of this, it appears that we can look forward to more own-root roses being introduced and sold at our local nurseries in the future. Own-root roses will eliminate suckering and hopefully will eventually help to eradicate mosaic virus.
Allow rose hips to develop by leaving dead flowers on the plant. The flowers are typically pollinated by insects, or pollinate themselves in some varieties, so there is no need to pollinate by hand unless you are breeding specific plants together. Leave the flowers on the rose plant without cutting them. After they wither, small fruits known as rose hips will develop in their place.
Alfalfa provides solid nutrition to roses, supplying nitrogen, calcium, iron, phosphorus, and other nutrients, including a fatty acid known to promote plant growth. Work alfalfa meal or pellets into soil around roses (1 cup per large bush; one-half cup for miniature roses). You can also brew alfalfa tea by soaking alfalfa meal or pellets in water. Discover tips on making and using alfalfa tea from the American Rose Society.
The Baggie Method: This was the first method I ever tried. Here you fill 2-inch plastic pots with potting soil, insert the rose stem halfway inside the pot, then put the pots into a one-gallon plastic zip-lock bag. You can get four 2-inch pots into each gallon bag. I didn't like this method because it caused many of the cuttings to rot since the bags tended to fold over and therefore prevented the air from circulating. The success rate of this method is not very good. It may be helpful to place a couple of small sticks inside the bag to help keep it upright and full of air.
Cover the cutting loosely, pot and all, with a plastic bag or plastic wrap and keep the soil moist. Putting a tall stake into the pot will hold the plastic away from the leaves. If the plastic touches the leaves, they remain wet and can succumb to a fungus disease. Along the same lines, make sure the condensation can escape from the plastic or the stem will rot.
Select two roses that you want to cross-pollenate. The blooms should not be too tight, perhaps about one-half to 3/4 open. Carefully peel off all the petals. The rose stamens inside should look golden yellow and fresh. With sterile tweezers or cuticle scissors, carefully remove all the stamens at the base of the rose hip, so you do not damage the pollen sacs (anthers). Place the rose stamens into separate, clean film canisters, and place the canisters in a dry place, but not in direct sunlight.
I would definitely mix in some compost with your garden soil as this will improve the structure of it. The dusting with fungicide is useful as it prevents the risk of infection, however, if you keep an eye on them and be ready to spring into action then it could be worth trying without . As for planting, I would personally keep them inside for a while, give them a chance to strengthen up before putting them outside in the elements!
A special stainless steel screen on the handle of the unit raises up when it is dry. When this happens, it throws the mercury switch which opens the solenoid valve and starts the misting cycle. When this stainless steel screen accumulates enough mist, the weight of the water drops it down again, shutting off the mercury switch, closing the solenoid valve. It needs practically no care or maintenance and can be left on, unattended day and night. This control unit is a very practical instrument which will have a long lifetime of carefree maintenance. There are no clocks to adjust, and it is not affected by water conditions. It works simply on the weight of water. The major benefit of the Mist-a-Matic is to control the misting cycle according to weather conditions. Too much water promotes disease and wastes water. Too little water causes leaves to wilt and failure to root. The Mist-a-Matic distributes the correct amount of water. In hot weather, the unit will turn on more frequently as the water evaporates. In cooler weather, the unit turns on less frequently. For operation, you will need to plug the unit into an electrical outlet. You need to hook it up to a water source with misting nozzles.
Black Spot: Rose plant leaves with black spots that eventually turn yellow have black spot. This is often caused by water splashing on leaves, especially in rainy weather. Leaves may require a protective fungicide coating, which would start in the summer before leaf spots started until first frost. Thoroughly clean up debris in the fall, and prune out all diseased canes.