A special stainless steel screen on the handle of the unit raises up when it is dry. When this happens, it throws the mercury switch which opens the solenoid valve and starts the misting cycle. When this stainless steel screen accumulates enough mist, the weight of the water drops it down again, shutting off the mercury switch, closing the solenoid valve. It needs practically no care or maintenance and can be left on, unattended day and night. This control unit is a very practical instrument which will have a long lifetime of carefree maintenance. There are no clocks to adjust, and it is not affected by water conditions. It works simply on the weight of water. The major benefit of the Mist-a-Matic is to control the misting cycle according to weather conditions. Too much water promotes disease and wastes water. Too little water causes leaves to wilt and failure to root. The Mist-a-Matic distributes the correct amount of water. In hot weather, the unit will turn on more frequently as the water evaporates. In cooler weather, the unit turns on less frequently. For operation, you will need to plug the unit into an electrical outlet. You need to hook it up to a water source with misting nozzles.
The ripened rose hip is then placed on a clean cutting board and cut in half to remove the seeds. Place the seeds in a clean container. Add some diluted bleach to kill off any bacteria and fungus spores. You can make the bleach by mixing drinking water with two teaspoons of household bleach. Stir the seeds well before rinsing them and using bottled water to remove all the bleach. To further clean and disinfect the seeds, put them in the container and add some hydrogen peroxide. The seeds can be soaked for up to 24 hours before rinsing them with clean water to clear all the hydrogen peroxide.
Some roses root easier than others — old-fashioned heirloom types often root better than modern hybrids — but don't let that keep you from trying your hand at replicating garden favorites and sharing your love of roses and gardening with family and friends. RootBoost™ and GardenTech® brands are here to help you learn and succeed in all your gardening projects, so you can experience all the joys of gardening.
Although miniature roses have always been grown on their own roots since the 1950's when they were first introduced, Ralph Moore of Sequoia Nursery in Visalia, CA, near Fresno, offered many of the larger roses on own-root along with his vast selection of minis. His Playgirl floribunda has always been sold by Ralph as own-root cuttings in 4-inch pots, as well as a good assortment of other own-root floribundas and old garden roses. Unfortunately, Mr. Moore is now deceased and his nursery is closed.
Taking rose cuttings can lead to a new crop of beautiful, successful roses. Like many other plants, it's important to choose a sunny spot for your rose cuttings that has moist soil. Cutting strong, healthy stems right above a set of leaves makes for great growing conditions, and dipping your cutting in a rooting hormone will help the roots take faster. By keeping your rose cuttings well hydrated, you'll have strong roots in no time.
Remove the seeds from the fridge. Try to do this around the time that the seeds would normally start to germinate, such as in early spring. Make sure that the environment outside of the fridge is about 70 degrees Fahrenheit. The seed will not sprout until you take them out of the fridge. Depending on the rose variety and individual seeds, the seeds could take anywhere from four to sixteen weeks to germinate. Often, 70% or more of the seeds never sprout at all.
After the rose seeds have soaked overnight, rinse them in a strainer and place them into the blender with at least a cup of plain purified water (making sure all seeds are covered), and turn it on for a few minutes. It usually doesn't chop up the seeds, but rather, it will clean off the pulp remaining from the rose hip, which would otherwise mold if left on the rose seed. You may see a few seeds chopped up, but those usually aren't viable anyway. Flush the rose seeds again through a strainer using fresh purified water.
The easiest way to begin experimenting with rose hybridizing, especially for the beginner, is to simply let some of your roses self-pollinate themselves, so they will "go to seed" and set hips. I have found that Playboy, Hurdy Gurdy, Peggy T and Fairhope are some of the easiest roses to set hips, and there are many others. Let the rose hips stay on the rose bushes at least four months before harvesting.
Take a sterile Q-Tip or small sable artist's brush, and dip it into the rose pollen you want to use. Then dab the pollen-coated Q-Tip or brush onto the stigma of the rose you have selected as the seed (female) parent. You could also simply use your finger to apply the pollen to the rose. Repeat this procedure after four hours, and then again after another four hours. Label the rose hip with the name of the seed parent as well as the pollen parent, i.e. Fairhope x Miss Flippins. The name that appears first is always the seed parent (the mother), and the second name is the pollen parent (the father).
I would definitely mix in some compost with your garden soil as this will improve the structure of it. The dusting with fungicide is useful as it prevents the risk of infection, however, if you keep an eye on them and be ready to spring into action then it could be worth trying without . As for planting, I would personally keep them inside for a while, give them a chance to strengthen up before putting them outside in the elements!
Select two roses that you want to cross-pollenate. The blooms should not be too tight, perhaps about one-half to 3/4 open. Carefully peel off all the petals. The rose stamens inside should look golden yellow and fresh. With sterile tweezers or cuticle scissors, carefully remove all the stamens at the base of the rose hip, so you do not damage the pollen sacs (anthers). Place the rose stamens into separate, clean film canisters, and place the canisters in a dry place, but not in direct sunlight.
Monitor the rose cuttings to ensure they’re hydrated and taking root. Keep an eye on the cuttings to make sure they’re never dried out, as well as to make sure the cuttings are taking root. You can test to see if the roots are growing by gently tugging on the cuttings. You should be able to feel a slight resistance after a week or 2, meaning the roots are growing well.