After the rose seeds have soaked overnight, rinse them in a strainer and place them into the blender with at least a cup of plain purified water (making sure all seeds are covered), and turn it on for a few minutes. It usually doesn't chop up the seeds, but rather, it will clean off the pulp remaining from the rose hip, which would otherwise mold if left on the rose seed. You may see a few seeds chopped up, but those usually aren't viable anyway. Flush the rose seeds again through a strainer using fresh purified water.
Why choose an old-fashioned rose over a modern hybrid? Many of the old rose varieties offer more fragrance, more complex and interesting blooms, greater disease resistance, easier care and more interesting forms. But modern roses can offer all-season blooms, and a much broader range of colors and flower forms. Some are also far more cold- hardy and disease-resistant than any of the old-fashioned varieties.
I too, have tried the cut rose flower method, but haven't yet been successful--perhaps because there are chemical additives that the roses have soaked up, or because there are no nodes (which are the points where new shoots grow out), or because the stems have spent much of their energy producing the flowers...BUT, perhaps if the flowers were immediately cut off and some rooting hormones applied to the bottom cut ends, that may work.
can someone help me. I am trying to propagate roses and planted the stems around 5 weeks ago. The stems beautifully grew leaves etc on its own but today when I took out one stem, it has only grown a callus so far. So my question is how long does it take for the roots to grow? When I started I moistened the soil a bit at that time and since then never again. Each stem is in a pot surrounded by a ziplock bag tied to it. All stems are growing leaves. Should I start watering them more often? Would that mean I have to take the bag off every time and then tie it again? Hoping to find some answers from more experienced people.
I have successfully taken rose cuttings with both new and old wood. It is important to let the new stems sufficiently mature. The new wood is usually mature enough after the stem has just finished blooming. If you don't let the stem mature enough, then it usually becomes limp and will die before you can get it to root. I take cuttings from new rose stems in the spring right after the first bloom cycle. Then in early to late fall (in Southern California) I prefer to use more mature or old wood. When using old wood in the fall, I will remove the rose cuttings from the Mason jar, baggie, or mister, after only several weeks since it is cool enough then for them to root on their own as long as I water them daily.
I bought hybrid tea roses last year. Not long after the first blooms, we moved one because it was interfering with the sprinkler system. It looked unhappy at first, but continued to bloom throughout the season. This year, it does not have so much as one leaf, no new foliage whatsoever, however, there is still green inside the stem towards the base of the cane. Is it done for, or is there a chance it will come back in it's second rear?
You may even wish to cut your cuttings down to 3" to 4" and double your plants, but they will be more prone to rot or dry up faster if you let the soil dry too long. The cuttings that are 6" to 8" seem to do much better, and if cuttings are even longer, the water has a longer length to travel up and down, and the cutting may end up more dehyrated with the upper part dying off. So 6" to 8" is a happy medium.
The next step when you grow roses from cuttings is to use a pencil or metal probe push down into the planting site soil to make a hole that is deep enough to plant the cutting up to about 50 percent of its overall length. Place the cutting that has been dipped into the rooting hormone into this hole. Lightly push the soil in around the cutting to finish the planting. Do the same thing for each cutting keeping them at least eight inches apart. Label each row of rose cuttings with the name of the mother rose bush it was taken from.
To start rose bush from cuttings, once the rose cuttings have been taken and brought to the planting site, take out a single cutting and remove the lower leaves only. Make a small slit with a sharp knife on one or two sides of the lower portion of the cutting, not a deep cut but just enough to penetrate the outer layer of the cutting. Dip the lower portion of the cutting into a rooting hormone powder.
Plant the seeds. Some store-bought seeds can be planted immediately. If you germinated your own seeds as described above, plant them as soon as they begin to sprout. Plant with the sprout pointed downward, as this is the root. Lightly cover them with soil, about 1/4 inch (6 mm) deep. Space seeds at least 2 inches (5 cm) apart to minimize competition.