Remove all but the top 2 leaflets on the stem, cutting just above the top set of leaves. You need to remove the excess leaves for the same reason we removed the flower in Step #2. They're taking up too much of the plant's energy. However we want the stem to continue to photosynthesize and feed itself until the new roots form, so we need to leave a couple of leaves.
Cathryn Chaney has worked as a gardening writer since 2002. Her horticultural experience working in the nursery industry informs her garden articles, especially those dealing with arid landscaping and drought-tolerant gardening. Chaney also writes poetry, which has appears in "Woman's World" magazine and elsewhere. Chaney graduated from the University of Arizona in 1992 with a Bachelor of Arts in English.
Fertilizer: Roses are heavy feeders, and will benefit from a steady supply of nitrogen, phosphorus and potassium. You can provide these nutrients with either liquid or granular fertilizers, at a ratio of approximately 5-8-5. In most cases, regular applications of compost, rotted manure, fish emulsion and seaweed extracts will provide roses with all the nutrients they need. These organic amendments also help to moderate pH imbalances and stimulate beneficial soil life. Other organic amendments favored by rose growers include greensand, black rock phosphate and alfalfa meal.
When you grow roses from seed, you are essentially developing new varieties of roses. If the rose fruit -- called a hip -- was produced by bee pollination, you don't know what varieties were crossed to get the seeds. Rose breeders hybridize chosen varieties and select for particular traits in resultant seedlings. However, each seedling will be a surprise. Rose seeds have to be collected in the fall, cleaned, and cold-treated before they are planted. Even though the cleaned seeds may look dry, they are not dry inside. If rose seeds are allowed to sit around in the open air and dry up completely, they will not grow.
The ripened rose hip is then placed on a clean cutting board and cut in half to remove the seeds. Place the seeds in a clean container. Add some diluted bleach to kill off any bacteria and fungus spores. You can make the bleach by mixing drinking water with two teaspoons of household bleach. Stir the seeds well before rinsing them and using bottled water to remove all the bleach. To further clean and disinfect the seeds, put them in the container and add some hydrogen peroxide. The seeds can be soaked for up to 24 hours before rinsing them with clean water to clear all the hydrogen peroxide.
Growing roses from seed can be challenging, since the majority of seeds you collect often won't germinate regardless of your efforts. Fortunately, most rose plants produce a large quantity of seeds inside their rose hips, so it usually isn't necessary to achieve a high success rate. Keep in mind that the plants that grow may be different in appearance or other characteristics from the mother plant, especially if that plant is a hybrid of two varieties grafted together.
Monitor the rose cuttings to ensure they’re hydrated and taking root. Keep an eye on the cuttings to make sure they’re never dried out, as well as to make sure the cuttings are taking root. You can test to see if the roots are growing by gently tugging on the cuttings. You should be able to feel a slight resistance after a week or 2, meaning the roots are growing well.
After the rose seeds have soaked overnight, rinse them in a strainer and place them into the blender with at least a cup of plain purified water (making sure all seeds are covered), and turn it on for a few minutes. It usually doesn't chop up the seeds, but rather, it will clean off the pulp remaining from the rose hip, which would otherwise mold if left on the rose seed. You may see a few seeds chopped up, but those usually aren't viable anyway. Flush the rose seeds again through a strainer using fresh purified water.
Prepare a large hole. You'll need one for each rose bush you're planting. Use a garden spade or shovel to dig a hole 18 inches (45.7 cm) wide and 18 inches (45.7 cm) deep. The measurements don't have to be exact, but a hole this wide and deep will be suitable for most roses. Mix the soil you removed from the hole with compost, and use some of it to form a small mound in the base of the hole. Add some bonemeal or rose fertilizer.
A gentle way to clean the rose seeds is to use a Cuisinart or other brand of blender with a dough blending attachment, which is made of plastic and does not have sharp blades. You can blend the rose seeds using this gentle dough attachment for several minutes without any damage to the seeds. Do not use a blender with sharp metal blades as damage to the rose seeds may occur.
Take a sterile Q-Tip or small sable artist's brush, and dip it into the rose pollen you want to use. Then dab the pollen-coated Q-Tip or brush onto the stigma of the rose you have selected as the seed (female) parent. You could also simply use your finger to apply the pollen to the rose. Repeat this procedure after four hours, and then again after another four hours. Label the rose hip with the name of the seed parent as well as the pollen parent, i.e. Fairhope x Miss Flippins. The name that appears first is always the seed parent (the mother), and the second name is the pollen parent (the father).
Ever wonder if you could root and grow roses from a branch of your favorite rose bush? Roses actually root rather easily. However most roses are grafted onto the rootstock of a different type of rose than the top, flowering portion, so the rose you root and grow may look nothing like the rose you started with. Grafting is done to improve strength, disease resistance, or hardiness, and even if you do get something resembling the parent rose you took your cutting from, it might not have that rose's hardiness. Rooting a rose cutting may not be hard to do, but it is something of a gamble.
Put the rose cuttings directly into water. It’s very important for the rose cuttings to stay hydrated so that they don’t dry out before you plant them. Immediately after you take the rose cuttings, put them in a cup of room temperature water until you’re ready to transfer them. Ideally, you’ll be ready to put them into the soil right after you cut the stems.
Pests and diseases: Prevention is the best way to avoid pest and disease problems. Start with disease-resistant varieties, keep plants in healthy condition (well fertilized and well watered), maintain good air circulation, keep foliage dry, and remove any diseased foliage or spent flowers. For Japanese beetle grubs, use beneficial nematodes or Milky Spore (Bacillus popilliae). Rose Rx is effective against scale, spidermites and aphids. For more information, see the Pest and Disease Finder.