A gentle way to clean the rose seeds is to use a Cuisinart or other brand of blender with a dough blending attachment, which is made of plastic and does not have sharp blades. You can blend the rose seeds using this gentle dough attachment for several minutes without any damage to the seeds. Do not use a blender with sharp metal blades as damage to the rose seeds may occur.
Monitor the rose cuttings to ensure they’re hydrated and taking root. Keep an eye on the cuttings to make sure they’re never dried out, as well as to make sure the cuttings are taking root. You can test to see if the roots are growing by gently tugging on the cuttings. You should be able to feel a slight resistance after a week or 2, meaning the roots are growing well.
Everybody has a story to tell of how their grandma would stick a piece of rose stem into the ground and then place a Mason Jar over the stem to make it grow. There are tales of how the early American settlers of the 1800's traveled to the far reaches of the wild west in covered wagons, with grandma bringing along "starts" of her favorite roses from back home. Perhaps the treasures of these "monsters on wooden wheels" were raided, and they discovered the Yellow Rose of Texas hiding under the bonnets of the women. Or maybe the settlers used their precious "starts" to barter for provisions along the endless dusty trails.
A special stainless steel screen on the handle of the unit raises up when it is dry. When this happens, it throws the mercury switch which opens the solenoid valve and starts the misting cycle. When this stainless steel screen accumulates enough mist, the weight of the water drops it down again, shutting off the mercury switch, closing the solenoid valve. It needs practically no care or maintenance and can be left on, unattended day and night. This control unit is a very practical instrument which will have a long lifetime of carefree maintenance. There are no clocks to adjust, and it is not affected by water conditions. It works simply on the weight of water. The major benefit of the Mist-a-Matic is to control the misting cycle according to weather conditions. Too much water promotes disease and wastes water. Too little water causes leaves to wilt and failure to root. The Mist-a-Matic distributes the correct amount of water. In hot weather, the unit will turn on more frequently as the water evaporates. In cooler weather, the unit turns on less frequently. For operation, you will need to plug the unit into an electrical outlet. You need to hook it up to a water source with misting nozzles.
NOTE: During my move, I had cut several rose branches and placed them in a grocery paper bag in my garage--only to have forgotten to bring them home for a week. The branches had been in a broiling hot enclosed garage without water, and needless to say, they looked pretty dried out to a crisp. But I didn't want to just toss them out yet (these were the climbing Charisma roses), so I got an empty plastic detergent tub and completely immersed the stems for 2 weeks (no changing water). Then I stuck them into soil and hoped for the best. Well, I got about a 50% survival rate.
Water the planted rose seeds well and place them outside in direct sunlight (no need for Grow Lights). If there is still danger of frost, then you will need to place the seed trays in a protected location such as under a tree or patio. You will need to keep the rose seed trays watered and don't let them dry out. After about six weeks, or when the weather starts to warm up, the little rose seedlings will start to sprout. They will continue to sprout as long as the weather is cool, but will stop sprouting when it gets too hot.
Water: Roses require more water than most other landscape plantings, especially during the first year as the plant is getting its roots established. The best way to water your roses is with drip irrigation. It concentrates the water at the root zone where it is needed, and keeps the foliage dry to minimize disease problems. A good, thick layer of organic mulch will help conserve moisture, reduce weeds, and encourage healthy root growth. As the mulch breaks down, it will also add organic matter to the soil.
Cover the stem with plastic or a mason jar. To cover the stem with plastic, insert two eight-inch (20-cm) sticks or wires into the soil on either side of the stem to prop up the plastic. Cover the pot and stem with a clear plastic bag, and affix the bag to the pot with an elastic or twine. With a mason jar, simply place a large mason jar over the stem.
Hi Katherine, You may have hit the reason. One of the most common reasons for roses not blooming well is the use of high nitrogen fertilizers or the over use of them. This will result in few to no blooms or small blooms and lots of foliage. Use a well balanced food or fertilizer when feeding your roses so that all of the rose’s nutritional needs are met.
Prepare a large hole. You'll need one for each rose bush you're planting. Use a garden spade or shovel to dig a hole 18 inches (45.7 cm) wide and 18 inches (45.7 cm) deep. The measurements don't have to be exact, but a hole this wide and deep will be suitable for most roses. Mix the soil you removed from the hole with compost, and use some of it to form a small mound in the base of the hole. Add some bonemeal or rose fertilizer.
There will be disappointments along the way, when many rose seeds fail to germinate, or perhaps they do germinate, only to die several weeks later from damp-off disease. Sometimes a rose seedling will turn out to be as ugly as sin, or very sickly, and you will reluctantly have to throw it away. Other times they will be just ho-hum, or look too much like its parent, and therefore have no value. But, just when you don't expect it, you might discover that one of your rose seedlings turns out to be very special.
Cover the cutting loosely, pot and all, with a plastic bag or plastic wrap and keep the soil moist. Putting a tall stake into the pot will hold the plastic away from the leaves. If the plastic touches the leaves, they remain wet and can succumb to a fungus disease. Along the same lines, make sure the condensation can escape from the plastic or the stem will rot.