Rose seeds need to go through stratification (an artificial cold spell) for 10 to 12 weeks before they will sprout. This, combined with a germination success rate of 20-30% makes propagation by seed an unattractive prospect. on by seed an unattractive prospect. If you still want to try it, find a good source of information that will guide you through the process.
Remove the rose hips once ripe. The rose hips will start out small and green, then change color as they grow until they are completely red, orange, brown, or purple. You may pick them at this point, or wait until they are just beginning to dry out and wrinkle. Don't wait until they are fully dry and brown, as the seeds inside may have died by this point.
Everybody has a story to tell of how their grandma would stick a piece of rose stem into the ground and then place a Mason Jar over the stem to make it grow. There are tales of how the early American settlers of the 1800's traveled to the far reaches of the wild west in covered wagons, with grandma bringing along "starts" of her favorite roses from back home. Perhaps the treasures of these "monsters on wooden wheels" were raided, and they discovered the Yellow Rose of Texas hiding under the bonnets of the women. Or maybe the settlers used their precious "starts" to barter for provisions along the endless dusty trails.
Caring for rose bushes is important to their overall health and vigor, especially when it comes to watering. Roses require at least an inch of water weekly throughout their growing season, beginning in spring or following spring planting. While overhead watering is suitable before the onset of new growth, it is often better to water these plants at the soil line using soaker hoses or similar means. Rose bushes are very susceptible to fungal diseases, such as black spot and powdery mildew, especially when their foliage is kept too wet.
Remove all but the top 2 leaflets on the stem, cutting just above the top set of leaves. You need to remove the excess leaves for the same reason we removed the flower in Step #2. They're taking up too much of the plant's energy. However we want the stem to continue to photosynthesize and feed itself until the new roots form, so we need to leave a couple of leaves.
Some people don't bother to take the time to do this, but others do. While the rose seeds are soaking, you will see that some sink to the bottom and some float on the top. The seeds that float are sometimes not viable, so you might want to throw them away. The rose seeds that sink are said to be the good ones, and are the ones to plant. There are pros and cons to this theory, and many rose hybridizers simply plant all the rose seeds that are harvested.   
Prepare a pot. Fill the small pot with potting soil. For the best results, replace a quarter of the soil with perlite, peat moss, or vermiculite, or a combination thereof. This will increase air flow and draining, giving your cutting a better opportunity to root.[2] If the soil is dry, water it and allow the excess water to drain out, so that the soil is evenly moist.
A special stainless steel screen on the handle of the unit raises up when it is dry. When this happens, it throws the mercury switch which opens the solenoid valve and starts the misting cycle. When this stainless steel screen accumulates enough mist, the weight of the water drops it down again, shutting off the mercury switch, closing the solenoid valve. It needs practically no care or maintenance and can be left on, unattended day and night. This control unit is a very practical instrument which will have a long lifetime of carefree maintenance. There are no clocks to adjust, and it is not affected by water conditions. It works simply on the weight of water. The major benefit of the Mist-a-Matic is to control the misting cycle according to weather conditions. Too much water promotes disease and wastes water. Too little water causes leaves to wilt and failure to root. The Mist-a-Matic distributes the correct amount of water. In hot weather, the unit will turn on more frequently as the water evaporates. In cooler weather, the unit turns on less frequently. For operation, you will need to plug the unit into an electrical outlet. You need to hook it up to a water source with misting nozzles.
After the rose seeds have soaked overnight, rinse them in a strainer and place them into the blender with at least a cup of plain purified water (making sure all seeds are covered), and turn it on for a few minutes. It usually doesn't chop up the seeds, but rather, it will clean off the pulp remaining from the rose hip, which would otherwise mold if left on the rose seed. You may see a few seeds chopped up, but those usually aren't viable anyway. Flush the rose seeds again through a strainer using fresh purified water.   
Monitor the rose cuttings to ensure they’re hydrated and taking root. Keep an eye on the cuttings to make sure they’re never dried out, as well as to make sure the cuttings are taking root. You can test to see if the roots are growing by gently tugging on the cuttings. You should be able to feel a slight resistance after a week or 2, meaning the roots are growing well.[13]
×