Caring for rose bushes is important to their overall health and vigor, especially when it comes to watering. Roses require at least an inch of water weekly throughout their growing season, beginning in spring or following spring planting. While overhead watering is suitable before the onset of new growth, it is often better to water these plants at the soil line using soaker hoses or similar means. Rose bushes are very susceptible to fungal diseases, such as black spot and powdery mildew, especially when their foliage is kept too wet.
A special stainless steel screen on the handle of the unit raises up when it is dry. When this happens, it throws the mercury switch which opens the solenoid valve and starts the misting cycle. When this stainless steel screen accumulates enough mist, the weight of the water drops it down again, shutting off the mercury switch, closing the solenoid valve. It needs practically no care or maintenance and can be left on, unattended day and night. This control unit is a very practical instrument which will have a long lifetime of carefree maintenance. There are no clocks to adjust, and it is not affected by water conditions. It works simply on the weight of water. The major benefit of the Mist-a-Matic is to control the misting cycle according to weather conditions. Too much water promotes disease and wastes water. Too little water causes leaves to wilt and failure to root. The Mist-a-Matic distributes the correct amount of water. In hot weather, the unit will turn on more frequently as the water evaporates. In cooler weather, the unit turns on less frequently. For operation, you will need to plug the unit into an electrical outlet. You need to hook it up to a water source with misting nozzles.
Prepare a large hole. You'll need one for each rose bush you're planting. Use a garden spade or shovel to dig a hole 18 inches (45.7 cm) wide and 18 inches (45.7 cm) deep. The measurements don't have to be exact, but a hole this wide and deep will be suitable for most roses. Mix the soil you removed from the hole with compost, and use some of it to form a small mound in the base of the hole. Add some bonemeal or rose fertilizer.

Put the rose cuttings directly into water. It’s very important for the rose cuttings to stay hydrated so that they don’t dry out before you plant them. Immediately after you take the rose cuttings, put them in a cup of room temperature water until you’re ready to transfer them. Ideally, you’ll be ready to put them into the soil right after you cut the stems.[3]

Remember that light changes as the angle of the sun shifts throughout the season. If you live in the upper half of the U.S., choose a site that will offer full sun year-round. The more sun you have, the more flowers your plants will produce. In the lower half of the U.S., choose spots with a little bit of afternoon shade. This protects blossoms from the scorching sun and helps your flowers last longer.

The ripened rose hip is then placed on a clean cutting board and cut in half to remove the seeds. Place the seeds in a clean container. Add some diluted bleach to kill off any bacteria and fungus spores. You can make the bleach by mixing drinking water with two teaspoons of household bleach. Stir the seeds well before rinsing them and using bottled water to remove all the bleach. To further clean and disinfect the seeds, put them in the container and add some hydrogen peroxide. The seeds can be soaked for up to 24 hours before rinsing them with clean water to clear all the hydrogen peroxide.
Prepare a pot. Fill the small pot with potting soil. For the best results, replace a quarter of the soil with perlite, peat moss, or vermiculite, or a combination thereof. This will increase air flow and draining, giving your cutting a better opportunity to root.[2] If the soil is dry, water it and allow the excess water to drain out, so that the soil is evenly moist.
The next step when you grow roses from cuttings is to use a pencil or metal probe push down into the planting site soil to make a hole that is deep enough to plant the cutting up to about 50 percent of its overall length. Place the cutting that has been dipped into the rooting hormone into this hole. Lightly push the soil in around the cutting to finish the planting. Do the same thing for each cutting keeping them at least eight inches apart. Label each row of rose cuttings with the name of the mother rose bush it was taken from.
While your cuttings take root, keep them covered and moist. In a garden bed, a simple DIY mini greenhouse does the trick. Just place a bell jar, a garden cloche or an overturned mason jar over the cutting. A clear plastic bottle with the bottom cut out and the cap removed works, too. Water the soil regularly to keep it moist, but not soggy. Your mini hothouse will keep the humidity high inside.
Pests and diseases: Prevention is the best way to avoid pest and disease problems. Start with disease-resistant varieties, keep plants in healthy condition (well fertilized and well watered), maintain good air circulation, keep foliage dry, and remove any diseased foliage or spent flowers. For Japanese beetle grubs, use beneficial nematodes or Milky Spore (Bacillus popilliae). Rose Rx is effective against scale, spidermites and aphids. For more information, see the Pest and Disease Finder.
×