Growing roses from seeds is not the fastest method for propagating roses but has several advantages. Roses from seeds take a little longer but then you end up developing a new set of varieties. Professional hybridisers select a new line of easy to grow and disease resistant rose to propagate. However, for you, each seedling will be a surprise when they finally bloom. It is like opening your birthday present when you were a kid. You never really knew what to expect! That is the same feeling seeing those little seedlings opens up for the first time.

A special stainless steel screen on the handle of the unit raises up when it is dry. When this happens, it throws the mercury switch which opens the solenoid valve and starts the misting cycle. When this stainless steel screen accumulates enough mist, the weight of the water drops it down again, shutting off the mercury switch, closing the solenoid valve. It needs practically no care or maintenance and can be left on, unattended day and night. This control unit is a very practical instrument which will have a long lifetime of carefree maintenance. There are no clocks to adjust, and it is not affected by water conditions. It works simply on the weight of water. The major benefit of the Mist-a-Matic is to control the misting cycle according to weather conditions. Too much water promotes disease and wastes water. Too little water causes leaves to wilt and failure to root. The Mist-a-Matic distributes the correct amount of water. In hot weather, the unit will turn on more frequently as the water evaporates. In cooler weather, the unit turns on less frequently. For operation, you will need to plug the unit into an electrical outlet. You need to hook it up to a water source with misting nozzles.
The next step when you grow roses from cuttings is to use a pencil or metal probe push down into the planting site soil to make a hole that is deep enough to plant the cutting up to about 50 percent of its overall length. Place the cutting that has been dipped into the rooting hormone into this hole. Lightly push the soil in around the cutting to finish the planting. Do the same thing for each cutting keeping them at least eight inches apart. Label each row of rose cuttings with the name of the mother rose bush it was taken from.
Just as with many other shrubs, roses can be grown from cuttings. It’s not a fast process – it may take a couple of years before your new plant produces flowers. But if you have a favourite rose, it can be fun to try. The cuttings need to be taken fresh from a healthy plant – don’t try to grow a new rose bush from the bunch of cut flowers you have sitting in a vase. And as roses bushes are pruned during winter, this is the most convenient time to take and pot up your rose cuttings.
Water: Roses require more water than most other landscape plantings, especially during the first year as the plant is getting its roots established. The best way to water your roses is with drip irrigation. It concentrates the water at the root zone where it is needed, and keeps the foliage dry to minimize disease problems. A good, thick layer of organic mulch will help conserve moisture, reduce weeds, and encourage healthy root growth. As the mulch breaks down, it will also add organic matter to the soil.

The Baggie Method: This was the first method I ever tried. Here you fill 2-inch plastic pots with potting soil, insert the rose stem halfway inside the pot, then put the pots into a one-gallon plastic zip-lock bag. You can get four 2-inch pots into each gallon bag. I didn't like this method because it caused many of the cuttings to rot since the bags tended to fold over and therefore prevented the air from circulating. The success rate of this method is not very good. It may be helpful to place a couple of small sticks inside the bag to help keep it upright and full of air.
If you order bare-root roses from a mail-order company, order early (late winter or early spring). The roses are usually shipped in the spring because bare roots when plants are fully dormant, well before they have leafed out. They’ll look like a bundle of sticks on arrival. Note that they are not dead—simply dormant. Check that the packing material is moist and keep them in a cool dark place until ready to plant.
Pick a sunny spot to plant your rose cuttings. Where you place your cuttings is especially important if you’re planning on growing them outdoors. Choose a spot that’s sunny but that’s not in direct sunlight — you don’t want them to dry out. Putting the rose cuttings in a pot or container is alright as well, just make sure the container is deep and wide enough for your rose cuttings to grow.[6]
To start rose bush from cuttings, once the rose cuttings have been taken and brought to the planting site, take out a single cutting and remove the lower leaves only. Make a small slit with a sharp knife on one or two sides of the lower portion of the cutting, not a deep cut but just enough to penetrate the outer layer of the cutting. Dip the lower portion of the cutting into a rooting hormone powder.

Fertilize the roses. After they are established, roses should be fertilized a few times per growing season. Use fertilizer (either liquid or granule) in early spring, when you see the first few leaves sprout. Use it again after the first bloom, and again if there's another bloom. Stop fertilizing the roses at the end of the summer, just before Labor Day.[7]
Hybrid teas and floribundas usually grow no more than 2 to 3 feet high. Their form is coarse, and hardly very appealing, but they do have the ability to produce an abundance of flowers throughout the growing season. The hybrid tea has large, single blooms on long, stiff stems, whereas the floribunda has slightly smaller clusters of blooms on stems that are not as stiff.
Cover the cutting loosely, pot and all, with a plastic bag or plastic wrap and keep the soil moist. Putting a tall stake into the pot will hold the plastic away from the leaves. If the plastic touches the leaves, they remain wet and can succumb to a fungus disease. Along the same lines, make sure the condensation can escape from the plastic or the stem will rot. 
×