I have successfully taken rose cuttings with both new and old wood. It is important to let the new stems sufficiently mature. The new wood is usually mature enough after the stem has just finished blooming. If you don't let the stem mature enough, then it usually becomes limp and will die before you can get it to root. I take cuttings from new rose stems in the spring right after the first bloom cycle. Then in early to late fall (in Southern California) I prefer to use more mature or old wood. When using old wood in the fall, I will remove the rose cuttings from the Mason jar, baggie, or mister, after only several weeks since it is cool enough then for them to root on their own as long as I water them daily.
After the rose seeds have soaked overnight, rinse them in a strainer and place them into the blender with at least a cup of plain purified water (making sure all seeds are covered), and turn it on for a few minutes. It usually doesn't chop up the seeds, but rather, it will clean off the pulp remaining from the rose hip, which would otherwise mold if left on the rose seed. You may see a few seeds chopped up, but those usually aren't viable anyway. Flush the rose seeds again through a strainer using fresh purified water.
Soaking the seeds is a crucial step if your seeds will germinate properly and stay clear of any diseases. You MUST not mix the bleach with the hydrogen peroxide as this results in a chemical reaction. 3% peroxide for 24 hours is just fine. This is also a good time to perform the water float test. Remove all seeds that float as they might not be viable.
A special stainless steel screen on the handle of the unit raises up when it is dry. When this happens, it throws the mercury switch which opens the solenoid valve and starts the misting cycle. When this stainless steel screen accumulates enough mist, the weight of the water drops it down again, shutting off the mercury switch, closing the solenoid valve. It needs practically no care or maintenance and can be left on, unattended day and night. This control unit is a very practical instrument which will have a long lifetime of carefree maintenance. There are no clocks to adjust, and it is not affected by water conditions. It works simply on the weight of water. The major benefit of the Mist-a-Matic is to control the misting cycle according to weather conditions. Too much water promotes disease and wastes water. Too little water causes leaves to wilt and failure to root. The Mist-a-Matic distributes the correct amount of water. In hot weather, the unit will turn on more frequently as the water evaporates. In cooler weather, the unit turns on less frequently. For operation, you will need to plug the unit into an electrical outlet. You need to hook it up to a water source with misting nozzles.
The Baggie Method: This was the first method I ever tried. Here you fill 2-inch plastic pots with potting soil, insert the rose stem halfway inside the pot, then put the pots into a one-gallon plastic zip-lock bag. You can get four 2-inch pots into each gallon bag. I didn't like this method because it caused many of the cuttings to rot since the bags tended to fold over and therefore prevented the air from circulating. The success rate of this method is not very good. It may be helpful to place a couple of small sticks inside the bag to help keep it upright and full of air.
When you grow roses from seed, you are essentially developing new varieties of roses. If the rose fruit -- called a hip -- was produced by bee pollination, you don't know what varieties were crossed to get the seeds. Rose breeders hybridize chosen varieties and select for particular traits in resultant seedlings. However, each seedling will be a surprise. Rose seeds have to be collected in the fall, cleaned, and cold-treated before they are planted. Even though the cleaned seeds may look dry, they are not dry inside. If rose seeds are allowed to sit around in the open air and dry up completely, they will not grow.
Please keep in mind that many rose bushes are grafted rose bushes. This means that the bottom part is a hardier rootstock that will withstand cold and heat better than the top and more desired part of the rose bush. Starting a rose bush from cuttings places the new rose bush on its own roots, so it may not be as hardy in cold climates or in extreme heat conditions climates. Being on its own root system can cause the new rose bush to be far less hardy than its mother rose bush.
One way to stratify the rose seeds is to place the cleaned seeds on a paper towel (a heavyweight brand such as Bounty). Then moisten the paper towel with a solution of half & half purified water and peroxide (to help prevent mold). Fold the paper towel closed, encasing all the rose seeds in the moistened paper towel. Then place the towel full of seeds into a plastic zippered bag. Mark the seed variety and date on the outside of the plastic bag with a permanent marker, and then place the bag into the refrigerator set at about 34-38 degrees. Never freeze the seeds, and do not let them dry out. The moistened paper towel should remain moist in the closed plastic bag for many weeks.
Fertilizer: Roses are heavy feeders, and will benefit from a steady supply of nitrogen, phosphorus and potassium. You can provide these nutrients with either liquid or granular fertilizers, at a ratio of approximately 5-8-5. In most cases, regular applications of compost, rotted manure, fish emulsion and seaweed extracts will provide roses with all the nutrients they need. These organic amendments also help to moderate pH imbalances and stimulate beneficial soil life. Other organic amendments favored by rose growers include greensand, black rock phosphate and alfalfa meal.