Caring for rose bushes is important to their overall health and vigor, especially when it comes to watering. Roses require at least an inch of water weekly throughout their growing season, beginning in spring or following spring planting. While overhead watering is suitable before the onset of new growth, it is often better to water these plants at the soil line using soaker hoses or similar means. Rose bushes are very susceptible to fungal diseases, such as black spot and powdery mildew, especially when their foliage is kept too wet.
After the rose seeds have soaked overnight, rinse them in a strainer and place them into the blender with at least a cup of plain purified water (making sure all seeds are covered), and turn it on for a few minutes. It usually doesn't chop up the seeds, but rather, it will clean off the pulp remaining from the rose hip, which would otherwise mold if left on the rose seed. You may see a few seeds chopped up, but those usually aren't viable anyway. Flush the rose seeds again through a strainer using fresh purified water.
Alfalfa provides solid nutrition to roses, supplying nitrogen, calcium, iron, phosphorus, and other nutrients, including a fatty acid known to promote plant growth. Work alfalfa meal or pellets into soil around roses (1 cup per large bush; one-half cup for miniature roses). You can also brew alfalfa tea by soaking alfalfa meal or pellets in water. Discover tips on making and using alfalfa tea from the American Rose Society.
A special stainless steel screen on the handle of the unit raises up when it is dry. When this happens, it throws the mercury switch which opens the solenoid valve and starts the misting cycle. When this stainless steel screen accumulates enough mist, the weight of the water drops it down again, shutting off the mercury switch, closing the solenoid valve. It needs practically no care or maintenance and can be left on, unattended day and night. This control unit is a very practical instrument which will have a long lifetime of carefree maintenance. There are no clocks to adjust, and it is not affected by water conditions. It works simply on the weight of water. The major benefit of the Mist-a-Matic is to control the misting cycle according to weather conditions. Too much water promotes disease and wastes water. Too little water causes leaves to wilt and failure to root. The Mist-a-Matic distributes the correct amount of water. In hot weather, the unit will turn on more frequently as the water evaporates. In cooler weather, the unit turns on less frequently. For operation, you will need to plug the unit into an electrical outlet. You need to hook it up to a water source with misting nozzles.
Label the canisters with the name of the pollen parent. Do not put a lid on the canister so they will dry out and not get moldy. After a few hours (on some rose varieties), or the next day (on other varieties), the pollen sacs will burst open, thereby releasing the pollen. Sometimes you will need to shake the canister so that the rose pollen will release from the pollen sacs. The black film canisters make it easy for you to see the pollen, which looks like a fine yellow powder. The pollen will stay fresh for about two weeks.
To plant in a garden, choose a spot with bright but indirect light, so cuttings won't be stressed by too much sun or heat. Northern and eastern exposures are perfect rooting spots. Cultivate the soil in your new propagation bed about 4 to 6 inches deep, so it crumbles easily. If your soil is heavy, incorporate a small amount of sand, so that new roots can penetrate without much effort.
I have successfully taken rose cuttings with both new and old wood. It is important to let the new stems sufficiently mature. The new wood is usually mature enough after the stem has just finished blooming. If you don't let the stem mature enough, then it usually becomes limp and will die before you can get it to root. I take cuttings from new rose stems in the spring right after the first bloom cycle. Then in early to late fall (in Southern California) I prefer to use more mature or old wood. When using old wood in the fall, I will remove the rose cuttings from the Mason jar, baggie, or mister, after only several weeks since it is cool enough then for them to root on their own as long as I water them daily.
Allow rose hips to develop by leaving dead flowers on the plant. The flowers are typically pollinated by insects, or pollinate themselves in some varieties, so there is no need to pollinate by hand unless you are breeding specific plants together. Leave the flowers on the rose plant without cutting them. After they wither, small fruits known as rose hips will develop in their place.
I too, have tried the cut rose flower method, but haven't yet been successful--perhaps because there are chemical additives that the roses have soaked up, or because there are no nodes (which are the points where new shoots grow out), or because the stems have spent much of their energy producing the flowers...BUT, perhaps if the flowers were immediately cut off and some rooting hormones applied to the bottom cut ends, that may work.
Despite their reputation for being finicky, most roses are simple to grow and easy to propagate at home. “Propagate" simply means to reproduce a plant easily from a simple cutting. Unlike seeds, which produce very different plants, rooted cuttings produce replicas of their parent. You don't have to be a trained rosarian to reproduce treasured family heirlooms or favorite garden roses.