After the rose seeds have soaked overnight, rinse them in a strainer and place them into the blender with at least a cup of plain purified water (making sure all seeds are covered), and turn it on for a few minutes. It usually doesn't chop up the seeds, but rather, it will clean off the pulp remaining from the rose hip, which would otherwise mold if left on the rose seed. You may see a few seeds chopped up, but those usually aren't viable anyway. Flush the rose seeds again through a strainer using fresh purified water.
I have four beautiful rose bushes that are my pride & joy! I spend every day tending them & just enjoying them in general. My issue, however, is that there are ALOT of cats in my neighborhood that find my flower beds a perfect litter box! I have tried everything, that I know of, to keep those pests out! I've gotten to the point that I'm about to bury razor wire under the mulch! Nothing that I try deterrs them & their owners won't keep them inside! PLEASE HELP!! ANY ideas are appreciated!
When you transplant your roses, be sure to dig a much bigger hole than you think you need (for most types, the planting hole should be about 15 to 18 inches wide), and add plenty of organic matter such as compost or aged manure. This will feed your plant in the years ahead. Some old-timers recommend placing a 4-inch square of gypsum wallboard and a 16-penny nail in the hole to provide calcium and iron, both appreciated by roses.
Plant the seeds. Some store-bought seeds can be planted immediately. If you germinated your own seeds as described above, plant them as soon as they begin to sprout. Plant with the sprout pointed downward, as this is the root. Lightly cover them with soil, about 1/4 inch (6 mm) deep. Space seeds at least 2 inches (5 cm) apart to minimize competition.
Hybrid teas and floribundas usually grow no more than 2 to 3 feet high. Their form is coarse, and hardly very appealing, but they do have the ability to produce an abundance of flowers throughout the growing season. The hybrid tea has large, single blooms on long, stiff stems, whereas the floribunda has slightly smaller clusters of blooms on stems that are not as stiff.
To plant in a garden, choose a spot with bright but indirect light, so cuttings won't be stressed by too much sun or heat. Northern and eastern exposures are perfect rooting spots. Cultivate the soil in your new propagation bed about 4 to 6 inches deep, so it crumbles easily. If your soil is heavy, incorporate a small amount of sand, so that new roots can penetrate without much effort.
I have successfully taken rose cuttings with both new and old wood. It is important to let the new stems sufficiently mature. The new wood is usually mature enough after the stem has just finished blooming. If you don't let the stem mature enough, then it usually becomes limp and will die before you can get it to root. I take cuttings from new rose stems in the spring right after the first bloom cycle. Then in early to late fall (in Southern California) I prefer to use more mature or old wood. When using old wood in the fall, I will remove the rose cuttings from the Mason jar, baggie, or mister, after only several weeks since it is cool enough then for them to root on their own as long as I water them daily.
Please keep in mind that many rose bushes are grafted rose bushes. This means that the bottom part is a hardier rootstock that will withstand cold and heat better than the top and more desired part of the rose bush. Starting a rose bush from cuttings places the new rose bush on its own roots, so it may not be as hardy in cold climates or in extreme heat conditions climates. Being on its own root system can cause the new rose bush to be far less hardy than its mother rose bush.
The next step when you grow roses from cuttings is to use a pencil or metal probe push down into the planting site soil to make a hole that is deep enough to plant the cutting up to about 50 percent of its overall length. Place the cutting that has been dipped into the rooting hormone into this hole. Lightly push the soil in around the cutting to finish the planting. Do the same thing for each cutting keeping them at least eight inches apart. Label each row of rose cuttings with the name of the mother rose bush it was taken from.
Hi Katherine, You may have hit the reason. One of the most common reasons for roses not blooming well is the use of high nitrogen fertilizers or the over use of them. This will result in few to no blooms or small blooms and lots of foliage. Use a well balanced food or fertilizer when feeding your roses so that all of the rose’s nutritional needs are met.
Black Spot: Rose plant leaves with black spots that eventually turn yellow have black spot. This is often caused by water splashing on leaves, especially in rainy weather. Leaves may require a protective fungicide coating, which would start in the summer before leaf spots started until first frost. Thoroughly clean up debris in the fall, and prune out all diseased canes.