While your cuttings take root, keep them covered and moist. In a garden bed, a simple DIY mini greenhouse does the trick. Just place a bell jar, a garden cloche or an overturned mason jar over the cutting. A clear plastic bottle with the bottom cut out and the cap removed works, too. Water the soil regularly to keep it moist, but not soggy. Your mini hothouse will keep the humidity high inside.
After the rose seeds have soaked overnight, rinse them in a strainer and place them into the blender with at least a cup of plain purified water (making sure all seeds are covered), and turn it on for a few minutes. It usually doesn't chop up the seeds, but rather, it will clean off the pulp remaining from the rose hip, which would otherwise mold if left on the rose seed. You may see a few seeds chopped up, but those usually aren't viable anyway. Flush the rose seeds again through a strainer using fresh purified water.
Soaking the seeds is a crucial step if your seeds will germinate properly and stay clear of any diseases. You MUST not mix the bleach with the hydrogen peroxide as this results in a chemical reaction. 3% peroxide for 24 hours is just fine. This is also a good time to perform the water float test. Remove all seeds that float as they might not be viable.
Take a sterile Q-Tip or small sable artist's brush, and dip it into the rose pollen you want to use. Then dab the pollen-coated Q-Tip or brush onto the stigma of the rose you have selected as the seed (female) parent. You could also simply use your finger to apply the pollen to the rose. Repeat this procedure after four hours, and then again after another four hours. Label the rose hip with the name of the seed parent as well as the pollen parent, i.e. Fairhope x Miss Flippins. The name that appears first is always the seed parent (the mother), and the second name is the pollen parent (the father).
Rose seeds need to go through stratification (an artificial cold spell) for 10 to 12 weeks before they will sprout. This, combined with a germination success rate of 20-30% makes propagation by seed an unattractive prospect. on by seed an unattractive prospect. If you still want to try it, find a good source of information that will guide you through the process.
Fertilizer: Roses are heavy feeders, and will benefit from a steady supply of nitrogen, phosphorus and potassium. You can provide these nutrients with either liquid or granular fertilizers, at a ratio of approximately 5-8-5. In most cases, regular applications of compost, rotted manure, fish emulsion and seaweed extracts will provide roses with all the nutrients they need. These organic amendments also help to moderate pH imbalances and stimulate beneficial soil life. Other organic amendments favored by rose growers include greensand, black rock phosphate and alfalfa meal.
Cover the stem with plastic or a mason jar. To cover the stem with plastic, insert two eight-inch (20-cm) sticks or wires into the soil on either side of the stem to prop up the plastic. Cover the pot and stem with a clear plastic bag, and affix the bag to the pot with an elastic or twine. With a mason jar, simply place a large mason jar over the stem.
Prepare a large hole. You'll need one for each rose bush you're planting. Use a garden spade or shovel to dig a hole 18 inches (45.7 cm) wide and 18 inches (45.7 cm) deep. The measurements don't have to be exact, but a hole this wide and deep will be suitable for most roses. Mix the soil you removed from the hole with compost, and use some of it to form a small mound in the base of the hole. Add some bonemeal or rose fertilizer.
Please keep in mind that many rose bushes are grafted rose bushes. This means that the bottom part is a hardier rootstock that will withstand cold and heat better than the top and more desired part of the rose bush. Starting a rose bush from cuttings places the new rose bush on its own roots, so it may not be as hardy in cold climates or in extreme heat conditions climates. Being on its own root system can cause the new rose bush to be far less hardy than its mother rose bush.
When pruning, be judicious. If you prune too hard in autumn, plants can be damaged beyond recovery. Instead, wait until spring, when plants begin to leaf out for the new season. (Roses are often not the earliest plants in the garden to respond to spring’s warming temperatures, so be patient.) Give the plant time to show its leaf buds then prune above that level.
Numerous things could be influencing the plant, from soil quality (do you amend and or feed/fertilize it?) to the circumstances of the move. It’s best to transplant roses in spring or ofall, not midsummer. and the new location should have plenty of organic matter/aged manure (these are amendments, per above). And then there’s watering … . So we really can not tell from here.
i believe the key to rooting a plant cutting in water is to keep it warm, but not sunburnt in strong full sun. my african violets all seem to root better in water than perlite or soil! the water level is determined by how the mother plant takes water--roses can take lots of water, so root in 3-5" of water. succulents dont like to stand in water, so root in 1/8" of water standing with only the base touching the water.
Black Spot: Rose plant leaves with black spots that eventually turn yellow have black spot. This is often caused by water splashing on leaves, especially in rainy weather. Leaves may require a protective fungicide coating, which would start in the summer before leaf spots started until first frost. Thoroughly clean up debris in the fall, and prune out all diseased canes.