There will be disappointments along the way, when many rose seeds fail to germinate, or perhaps they do germinate, only to die several weeks later from damp-off disease. Sometimes a rose seedling will turn out to be as ugly as sin, or very sickly, and you will reluctantly have to throw it away. Other times they will be just ho-hum, or look too much like its parent, and therefore have no value. But, just when you don't expect it, you might discover that one of your rose seedlings turns out to be very special.
So grandma had the right idea in the first place, and she really did know what she was doing. It has always been fun to start roses from cuttings. Some people get their kicks by going "rose rustling" in the deserted cemeteries of old and forgotten mining towns. Others just take a twig from their favorite rose and stick it into the ground in their backyard. There is nothing complicated nor scientific about taking cuttings of roses and rooting them to "start" a new plant. There are various ways of taking rose cuttings, so let's tell you how.
Ever wonder if you could root and grow roses from a branch of your favorite rose bush? Roses actually root rather easily. However most roses are grafted onto the rootstock of a different type of rose than the top, flowering portion, so the rose you root and grow may look nothing like the rose you started with. Grafting is done to improve strength, disease resistance, or hardiness, and even if you do get something resembling the parent rose you took your cutting from, it might not have that rose's hardiness. Rooting a rose cutting may not be hard to do, but it is something of a gamble.
The Baggie Method: This was the first method I ever tried. Here you fill 2-inch plastic pots with potting soil, insert the rose stem halfway inside the pot, then put the pots into a one-gallon plastic zip-lock bag. You can get four 2-inch pots into each gallon bag. I didn't like this method because it caused many of the cuttings to rot since the bags tended to fold over and therefore prevented the air from circulating. The success rate of this method is not very good. It may be helpful to place a couple of small sticks inside the bag to help keep it upright and full of air.
Remember that light changes as the angle of the sun shifts throughout the season. If you live in the upper half of the U.S., choose a site that will offer full sun year-round. The more sun you have, the more flowers your plants will produce. In the lower half of the U.S., choose spots with a little bit of afternoon shade. This protects blossoms from the scorching sun and helps your flowers last longer.
The next step when you grow roses from cuttings is to use a pencil or metal probe push down into the planting site soil to make a hole that is deep enough to plant the cutting up to about 50 percent of its overall length. Place the cutting that has been dipped into the rooting hormone into this hole. Lightly push the soil in around the cutting to finish the planting. Do the same thing for each cutting keeping them at least eight inches apart. Label each row of rose cuttings with the name of the mother rose bush it was taken from.
I am curious... it seems that you are just supposed to "soak" the cut stems for a week or more in water.... which is mostly what people normally do with cut roses. But whenever I put roses my boyfriend brings me in water, they just fade within a week or so. I'll "feed" the roses with either sugar in the water or with the packet of plant food that comes with them. I'll cut off a small bit at an angle from the bottom of the stem evert day or so. But after a week or so they start wilting and drooping, so at that point I just take them out and hang them upside down to dry.
A special stainless steel screen on the handle of the unit raises up when it is dry. When this happens, it throws the mercury switch which opens the solenoid valve and starts the misting cycle. When this stainless steel screen accumulates enough mist, the weight of the water drops it down again, shutting off the mercury switch, closing the solenoid valve. It needs practically no care or maintenance and can be left on, unattended day and night. This control unit is a very practical instrument which will have a long lifetime of carefree maintenance. There are no clocks to adjust, and it is not affected by water conditions. It works simply on the weight of water. The major benefit of the Mist-a-Matic is to control the misting cycle according to weather conditions. Too much water promotes disease and wastes water. Too little water causes leaves to wilt and failure to root. The Mist-a-Matic distributes the correct amount of water. In hot weather, the unit will turn on more frequently as the water evaporates. In cooler weather, the unit turns on less frequently. For operation, you will need to plug the unit into an electrical outlet. You need to hook it up to a water source with misting nozzles.
Cover the cutting loosely, pot and all, with a plastic bag or plastic wrap and keep the soil moist. Putting a tall stake into the pot will hold the plastic away from the leaves. If the plastic touches the leaves, they remain wet and can succumb to a fungus disease. Along the same lines, make sure the condensation can escape from the plastic or the stem will rot.