Fertilize the roses. After they are established, roses should be fertilized a few times per growing season. Use fertilizer (either liquid or granule) in early spring, when you see the first few leaves sprout. Use it again after the first bloom, and again if there's another bloom. Stop fertilizing the roses at the end of the summer, just before Labor Day.
Prepare a large hole. You'll need one for each rose bush you're planting. Use a garden spade or shovel to dig a hole 18 inches (45.7 cm) wide and 18 inches (45.7 cm) deep. The measurements don't have to be exact, but a hole this wide and deep will be suitable for most roses. Mix the soil you removed from the hole with compost, and use some of it to form a small mound in the base of the hole. Add some bonemeal or rose fertilizer.
There will be disappointments along the way, when many rose seeds fail to germinate, or perhaps they do germinate, only to die several weeks later from damp-off disease. Sometimes a rose seedling will turn out to be as ugly as sin, or very sickly, and you will reluctantly have to throw it away. Other times they will be just ho-hum, or look too much like its parent, and therefore have no value. But, just when you don't expect it, you might discover that one of your rose seedlings turns out to be very special.
Hi, I put almost 30 cuttings on water for 2 weeks until buds and little leaves came out from approximately 20 of them. I've put them on separate pots afterwards and gave them a little bit of water every day in order to maintain humid the soil but they are all drying to death! Do not know what to do! Anybody that could help? Not putting the bag as I have them inside with a room temperature around 73,4 F.
Hybrid teas and floribundas usually grow no more than 2 to 3 feet high. Their form is coarse, and hardly very appealing, but they do have the ability to produce an abundance of flowers throughout the growing season. The hybrid tea has large, single blooms on long, stiff stems, whereas the floribunda has slightly smaller clusters of blooms on stems that are not as stiff.
The Baggie Method: This was the first method I ever tried. Here you fill 2-inch plastic pots with potting soil, insert the rose stem halfway inside the pot, then put the pots into a one-gallon plastic zip-lock bag. You can get four 2-inch pots into each gallon bag. I didn't like this method because it caused many of the cuttings to rot since the bags tended to fold over and therefore prevented the air from circulating. The success rate of this method is not very good. It may be helpful to place a couple of small sticks inside the bag to help keep it upright and full of air.
After the rose seeds have soaked overnight, rinse them in a strainer and place them into the blender with at least a cup of plain purified water (making sure all seeds are covered), and turn it on for a few minutes. It usually doesn't chop up the seeds, but rather, it will clean off the pulp remaining from the rose hip, which would otherwise mold if left on the rose seed. You may see a few seeds chopped up, but those usually aren't viable anyway. Flush the rose seeds again through a strainer using fresh purified water.
Cathryn Chaney has worked as a gardening writer since 2002. Her horticultural experience working in the nursery industry informs her garden articles, especially those dealing with arid landscaping and drought-tolerant gardening. Chaney also writes poetry, which has appears in "Woman's World" magazine and elsewhere. Chaney graduated from the University of Arizona in 1992 with a Bachelor of Arts in English.
Rose seeds need to go through stratification (an artificial cold spell) for 10 to 12 weeks before they will sprout. This, combined with a germination success rate of 20-30% makes propagation by seed an unattractive prospect. on by seed an unattractive prospect. If you still want to try it, find a good source of information that will guide you through the process.
Cover the cutting loosely, pot and all, with a plastic bag or plastic wrap and keep the soil moist. Putting a tall stake into the pot will hold the plastic away from the leaves. If the plastic touches the leaves, they remain wet and can succumb to a fungus disease. Along the same lines, make sure the condensation can escape from the plastic or the stem will rot.