The ripened rose hip is then placed on a clean cutting board and cut in half to remove the seeds. Place the seeds in a clean container. Add some diluted bleach to kill off any bacteria and fungus spores. You can make the bleach by mixing drinking water with two teaspoons of household bleach. Stir the seeds well before rinsing them and using bottled water to remove all the bleach. To further clean and disinfect the seeds, put them in the container and add some hydrogen peroxide. The seeds can be soaked for up to 24 hours before rinsing them with clean water to clear all the hydrogen peroxide.
Some roses root easier than others — old-fashioned heirloom types often root better than modern hybrids — but don't let that keep you from trying your hand at replicating garden favorites and sharing your love of roses and gardening with family and friends. RootBoost™ and GardenTech® brands are here to help you learn and succeed in all your gardening projects, so you can experience all the joys of gardening.
While your cuttings take root, keep them covered and moist. In a garden bed, a simple DIY mini greenhouse does the trick. Just place a bell jar, a garden cloche or an overturned mason jar over the cutting. A clear plastic bottle with the bottom cut out and the cap removed works, too. Water the soil regularly to keep it moist, but not soggy. Your mini hothouse will keep the humidity high inside.
After the rose seeds have soaked overnight, rinse them in a strainer and place them into the blender with at least a cup of plain purified water (making sure all seeds are covered), and turn it on for a few minutes. It usually doesn't chop up the seeds, but rather, it will clean off the pulp remaining from the rose hip, which would otherwise mold if left on the rose seed. You may see a few seeds chopped up, but those usually aren't viable anyway. Flush the rose seeds again through a strainer using fresh purified water.
A special stainless steel screen on the handle of the unit raises up when it is dry. When this happens, it throws the mercury switch which opens the solenoid valve and starts the misting cycle. When this stainless steel screen accumulates enough mist, the weight of the water drops it down again, shutting off the mercury switch, closing the solenoid valve. It needs practically no care or maintenance and can be left on, unattended day and night. This control unit is a very practical instrument which will have a long lifetime of carefree maintenance. There are no clocks to adjust, and it is not affected by water conditions. It works simply on the weight of water. The major benefit of the Mist-a-Matic is to control the misting cycle according to weather conditions. Too much water promotes disease and wastes water. Too little water causes leaves to wilt and failure to root. The Mist-a-Matic distributes the correct amount of water. In hot weather, the unit will turn on more frequently as the water evaporates. In cooler weather, the unit turns on less frequently. For operation, you will need to plug the unit into an electrical outlet. You need to hook it up to a water source with misting nozzles.
Next fill your trays or pots with the potting soil. You can opt to use 50% sterile potting soil and 50% vermiculite, or half peat and half perlite. When the potting mix is ready in the trays or pots, this is the time to take off your seeds from the towel. Remember the seeds must not be removed from the plastic bag until they are ready to be planted. You lightly dust them before planting.
Prepare a pot. Fill the small pot with potting soil. For the best results, replace a quarter of the soil with perlite, peat moss, or vermiculite, or a combination thereof. This will increase air flow and draining, giving your cutting a better opportunity to root. If the soil is dry, water it and allow the excess water to drain out, so that the soil is evenly moist.
I planted mine in to the ground just like a normal rose bush, amending the soil with rose fertilizer and alfalfa meal. It is gorgeous, but because it's low to the ground, you should make sure to use drip irrigation or a soaker hose to water it so it doesn’t get black spots from the water splashing on the leaves. If yours is in a pot, let it go dormant in the garage or close to your home to keep the pot from freezing. Keep it watered and in the spring it should come back with more fertilizer to keep it happy.
Wonderful instructable! And THANK YOU! I have the most beautiful smelling rose in my backyard that was there when my father purchased the house (I purchased it from him... the house, not the rose, the rose just came with it :) ) and I've never been able to identify it or find anything that smelled nearly as sweet. It blossoms with two buds a year, consistantly, never producing more or growing any further. Both buds are now dead so I think I will cut them off the moment I get home and start this process. Maybe in a couple of years I'll have a whole patch of these magnificent bushes. Again, many kudos and thanks.
Taking rose cuttings can lead to a new crop of beautiful, successful roses. Like many other plants, it's important to choose a sunny spot for your rose cuttings that has moist soil. Cutting strong, healthy stems right above a set of leaves makes for great growing conditions, and dipping your cutting in a rooting hormone will help the roots take faster. By keeping your rose cuttings well hydrated, you'll have strong roots in no time.