Prepare a large hole. You'll need one for each rose bush you're planting. Use a garden spade or shovel to dig a hole 18 inches (45.7 cm) wide and 18 inches (45.7 cm) deep. The measurements don't have to be exact, but a hole this wide and deep will be suitable for most roses. Mix the soil you removed from the hole with compost, and use some of it to form a small mound in the base of the hole. Add some bonemeal or rose fertilizer.
Select the pollen parent flower. Remove the petals and harvest the stamens -- the male flower part that has the pollen -- as in the previous two steps. Check the stamens immediately to see if they are producing fluffy, mature, yellow pollen. If so, proceed to pollination. If not, look at stamens in the vials daily. Use them for pollination when mature pollen is coming loose from the stamens.
Next fill your trays or pots with the potting soil. You can opt to use 50% sterile potting soil and 50% vermiculite, or half peat and half perlite. When the potting mix is ready in the trays or pots, this is the time to take off your seeds from the towel. Remember the seeds must not be removed from the plastic bag until they are ready to be planted. You lightly dust them before planting.
The next step when you grow roses from cuttings is to use a pencil or metal probe push down into the planting site soil to make a hole that is deep enough to plant the cutting up to about 50 percent of its overall length. Place the cutting that has been dipped into the rooting hormone into this hole. Lightly push the soil in around the cutting to finish the planting. Do the same thing for each cutting keeping them at least eight inches apart. Label each row of rose cuttings with the name of the mother rose bush it was taken from.
I have successfully taken rose cuttings with both new and old wood. It is important to let the new stems sufficiently mature. The new wood is usually mature enough after the stem has just finished blooming. If you don't let the stem mature enough, then it usually becomes limp and will die before you can get it to root. I take cuttings from new rose stems in the spring right after the first bloom cycle. Then in early to late fall (in Southern California) I prefer to use more mature or old wood. When using old wood in the fall, I will remove the rose cuttings from the Mason jar, baggie, or mister, after only several weeks since it is cool enough then for them to root on their own as long as I water them daily.
After the rose seeds have soaked overnight, rinse them in a strainer and place them into the blender with at least a cup of plain purified water (making sure all seeds are covered), and turn it on for a few minutes. It usually doesn't chop up the seeds, but rather, it will clean off the pulp remaining from the rose hip, which would otherwise mold if left on the rose seed. You may see a few seeds chopped up, but those usually aren't viable anyway. Flush the rose seeds again through a strainer using fresh purified water.
To plant in a garden, choose a spot with bright but indirect light, so cuttings won't be stressed by too much sun or heat. Northern and eastern exposures are perfect rooting spots. Cultivate the soil in your new propagation bed about 4 to 6 inches deep, so it crumbles easily. If your soil is heavy, incorporate a small amount of sand, so that new roots can penetrate without much effort.
Place a jar over each cutting to form a sort of miniature greenhouse for each cutting. It is extremely important that the soil moisture for the cuttings does not dry out at this rooting time. The jar will help to hold humidity in, but can be a problem if it is subjected to a lot of hot afternoon sun, as it will overheat the cutting and kill it, thus the need for shielding against the exposure to the hot afternoon sun when you root roses. Watering of the planting site every other day may be required to keep the soil moist but do not create a standing water or muddy soils situation.
Cover the cutting loosely, pot and all, with a plastic bag or plastic wrap and keep the soil moist. Putting a tall stake into the pot will hold the plastic away from the leaves. If the plastic touches the leaves, they remain wet and can succumb to a fungus disease. Along the same lines, make sure the condensation can escape from the plastic or the stem will rot.
Northern gardeners need to know exactly what zone a rose is hardy to. Southern gardeners must also watch to see what zones are recommended for each particular variety, as some roses perform very poorly in hot and/or humid weather. Read the catalogs carefully and, if possible, purchase your roses from a local or regional grower. They will be able to advise you from experience about how a particular variety will perform in your area.
I would definitely mix in some compost with your garden soil as this will improve the structure of it. The dusting with fungicide is useful as it prevents the risk of infection, however, if you keep an eye on them and be ready to spring into action then it could be worth trying without . As for planting, I would personally keep them inside for a while, give them a chance to strengthen up before putting them outside in the elements!
The next step how to grow roses from seed is to sprout the rose seeds. After having gone through their “stratification” time, take the containers out of the refrigerator and into a warm environment of around 70 F. (21 C.). I do my best to time this for early spring when the seedlings would normally be coming out of their cold cycle (stratification) outside and starting to sprout.
Remove the seeds from the fridge. Try to do this around the time that the seeds would normally start to germinate, such as in early spring. Make sure that the environment outside of the fridge is about 70 degrees Fahrenheit. The seed will not sprout until you take them out of the fridge. Depending on the rose variety and individual seeds, the seeds could take anywhere from four to sixteen weeks to germinate. Often, 70% or more of the seeds never sprout at all.
Pruning: Dead, weak and sickly stems can lead to disease problems. Pruning these away will increase air circulation to the center of the plant and minimize fungus problems. Pruning also stimulates new growth, and allows you to shape the plant in a pleasing manner. Spent flowers should be removed during the growing season to encourage reblooming. Use a scissor-action pruner for the cleanest cuts.
Prepare a pot. Fill the small pot with potting soil. For the best results, replace a quarter of the soil with perlite, peat moss, or vermiculite, or a combination thereof. This will increase air flow and draining, giving your cutting a better opportunity to root. If the soil is dry, water it and allow the excess water to drain out, so that the soil is evenly moist.
While your cuttings take root, keep them covered and moist. In a garden bed, a simple DIY mini greenhouse does the trick. Just place a bell jar, a garden cloche or an overturned mason jar over the cutting. A clear plastic bottle with the bottom cut out and the cap removed works, too. Water the soil regularly to keep it moist, but not soggy. Your mini hothouse will keep the humidity high inside.