The Baggie Method: This was the first method I ever tried. Here you fill 2-inch plastic pots with potting soil, insert the rose stem halfway inside the pot, then put the pots into a one-gallon plastic zip-lock bag. You can get four 2-inch pots into each gallon bag. I didn't like this method because it caused many of the cuttings to rot since the bags tended to fold over and therefore prevented the air from circulating. The success rate of this method is not very good. It may be helpful to place a couple of small sticks inside the bag to help keep it upright and full of air.
As soon as the rose seeds have been removed from the rose hips, rinse the seeds in a solution of purified water (any bottled water will do) with 5% bleach. This would be about two teaspoons of bleach per cup of water. Rinse the rose seeds with plain bottled water in a strainer, then soak the seeds in straight 3% peroxide for 24 hours. CAUTION: Do not mix bleach with peroxide because there could be a chemical reaction.
Select two roses that you want to cross-pollenate. The blooms should not be too tight, perhaps about one-half to 3/4 open. Carefully peel off all the petals. The rose stamens inside should look golden yellow and fresh. With sterile tweezers or cuticle scissors, carefully remove all the stamens at the base of the rose hip, so you do not damage the pollen sacs (anthers). Place the rose stamens into separate, clean film canisters, and place the canisters in a dry place, but not in direct sunlight.
This is a fungus called black spot. Left untreated, it can cause all the leaves on your roses to turn yellow and fall off. It will also affect nearby plants, as it spreads by spores. Remove ALL INFECTED material and throw it away or burn it. Do NOT leave it on the ground as this fungus is very hardy. It can survive winter and travels very easily, even after being removed from the affected plant. Spray your plants regularly (bi-weekly) in the growing season with a good fungicide (I like the Bayer products). You can also add a little bit of dish soap and baking soda to a spray bottle with water and spray the entire plant.
The rose seeds can be planted right away if you have harvested them as late as November, December or January (in Southern California) or early spring after danger of frosts in your area. Place the rose seeds about one-half inch deep in a very light mixture of 50% sterile potting soil and 50% vermiculite. Some rose hybridizers use Sunshine Mix #4. You can use small pots or shallow trays to plant your seeds, whatever works for the space you have, as long as they have good drainage. Nursery flats work well for this. Lightly dust the rose seeds with RooTone or Captan before covering with soil. And then dust the top of the soil again, which will hopefully help to prevent damp-off (a disease which kills young rose seedlings). Amateur rose hybridizers concerned with toxic chemicals may want to periodically spray the seed tray with diluted peroxide and water instead of the more toxic Captan.
Monitor the rose cuttings to ensure they’re hydrated and taking root. Keep an eye on the cuttings to make sure they’re never dried out, as well as to make sure the cuttings are taking root. You can test to see if the roots are growing by gently tugging on the cuttings. You should be able to feel a slight resistance after a week or 2, meaning the roots are growing well.
Growing roses from seeds is not the fastest method for propagating roses but has several advantages. Roses from seeds take a little longer but then you end up developing a new set of varieties. Professional hybridisers select a new line of easy to grow and disease resistant rose to propagate. However, for you, each seedling will be a surprise when they finally bloom. It is like opening your birthday present when you were a kid. You never really knew what to expect! That is the same feeling seeing those little seedlings opens up for the first time.
I have successfully taken rose cuttings with both new and old wood. It is important to let the new stems sufficiently mature. The new wood is usually mature enough after the stem has just finished blooming. If you don't let the stem mature enough, then it usually becomes limp and will die before you can get it to root. I take cuttings from new rose stems in the spring right after the first bloom cycle. Then in early to late fall (in Southern California) I prefer to use more mature or old wood. When using old wood in the fall, I will remove the rose cuttings from the Mason jar, baggie, or mister, after only several weeks since it is cool enough then for them to root on their own as long as I water them daily.