A special stainless steel screen on the handle of the unit raises up when it is dry. When this happens, it throws the mercury switch which opens the solenoid valve and starts the misting cycle. When this stainless steel screen accumulates enough mist, the weight of the water drops it down again, shutting off the mercury switch, closing the solenoid valve. It needs practically no care or maintenance and can be left on, unattended day and night. This control unit is a very practical instrument which will have a long lifetime of carefree maintenance. There are no clocks to adjust, and it is not affected by water conditions. It works simply on the weight of water. The major benefit of the Mist-a-Matic is to control the misting cycle according to weather conditions. Too much water promotes disease and wastes water. Too little water causes leaves to wilt and failure to root. The Mist-a-Matic distributes the correct amount of water. In hot weather, the unit will turn on more frequently as the water evaporates. In cooler weather, the unit turns on less frequently. For operation, you will need to plug the unit into an electrical outlet. You need to hook it up to a water source with misting nozzles.
The Baggie Method: This was the first method I ever tried. Here you fill 2-inch plastic pots with potting soil, insert the rose stem halfway inside the pot, then put the pots into a one-gallon plastic zip-lock bag. You can get four 2-inch pots into each gallon bag. I didn't like this method because it caused many of the cuttings to rot since the bags tended to fold over and therefore prevented the air from circulating. The success rate of this method is not very good. It may be helpful to place a couple of small sticks inside the bag to help keep it upright and full of air.
To plant in a garden, choose a spot with bright but indirect light, so cuttings won't be stressed by too much sun or heat. Northern and eastern exposures are perfect rooting spots. Cultivate the soil in your new propagation bed about 4 to 6 inches deep, so it crumbles easily. If your soil is heavy, incorporate a small amount of sand, so that new roots can penetrate without much effort.
The Misting Method: As you get more sophisticated in your rose propagating methods you may eventually want to set up a misting bench. It can be an open-air bench or one enclosed in a greenhouse, or even a small misting box, similar to the one my husband Bob built for me. (Refer to "How We Made Our Misting Box," from Rose Ecstasy. You could choose to rig it up with a manual or an automatically-timed mister, whatever your time, money, or expertise will allow. I am fortunate to have a very handy guy for a husband, who is a good sport whenever I come up with these crazy project ideas.
Soaking the seeds is a crucial step if your seeds will germinate properly and stay clear of any diseases. You MUST not mix the bleach with the hydrogen peroxide as this results in a chemical reaction. 3% peroxide for 24 hours is just fine. This is also a good time to perform the water float test. Remove all seeds that float as they might not be viable.
Hi Katherine, You may have hit the reason. One of the most common reasons for roses not blooming well is the use of high nitrogen fertilizers or the over use of them. This will result in few to no blooms or small blooms and lots of foliage. Use a well balanced food or fertilizer when feeding your roses so that all of the rose’s nutritional needs are met.
Español: cultivar rosas usando semillas, Italiano: Coltivare le Rose Usando i Semi, Português: Cultivar Rosas a Partir da Semente, Русский: вырастить розы из семян, 中文: 用种子种玫瑰, Deutsch: Aus Samenkörnern Rosen ziehen, Français: faire pousser des roses à partir de graines, Nederlands: Rozen kweken uit zaad, Bahasa Indonesia: Menanam Bunga Mawar dari Biji, العربية: زراعة الورود من البذرة, Tiếng Việt: Trồng hoa hồng từ hạt, 日本語: バラを種から育てる, 한국어: 씨앗으로 장미 기르는 방법