One way to stratify the rose seeds is to place the cleaned seeds on a paper towel (a heavyweight brand such as Bounty). Then moisten the paper towel with a solution of half & half purified water and peroxide (to help prevent mold). Fold the paper towel closed, encasing all the rose seeds in the moistened paper towel. Then place the towel full of seeds into a plastic zippered bag. Mark the seed variety and date on the outside of the plastic bag with a permanent marker, and then place the bag into the refrigerator set at about 34-38 degrees. Never freeze the seeds, and do not let them dry out. The moistened paper towel should remain moist in the closed plastic bag for many weeks.   

Some people don't bother to take the time to do this, but others do. While the rose seeds are soaking, you will see that some sink to the bottom and some float on the top. The seeds that float are sometimes not viable, so you might want to throw them away. The rose seeds that sink are said to be the good ones, and are the ones to plant. There are pros and cons to this theory, and many rose hybridizers simply plant all the rose seeds that are harvested.   


Rose seeds need to go through stratification (an artificial cold spell) for 10 to 12 weeks before they will sprout. This, combined with a germination success rate of 20-30% makes propagation by seed an unattractive prospect. on by seed an unattractive prospect. If you still want to try it, find a good source of information that will guide you through the process.
Pick a sunny spot to plant your rose cuttings. Where you place your cuttings is especially important if you’re planning on growing them outdoors. Choose a spot that’s sunny but that’s not in direct sunlight — you don’t want them to dry out. Putting the rose cuttings in a pot or container is alright as well, just make sure the container is deep and wide enough for your rose cuttings to grow.[6]

You may even wish to cut your cuttings down to 3" to 4" and double your plants, but they will be more prone to rot or dry up faster if you let the soil dry too long. The cuttings that are 6" to 8" seem to do much better, and if cuttings are even longer, the water has a longer length to travel up and down, and the cutting may end up more dehyrated with the upper part dying off. So 6" to 8" is a happy medium.
As soon as the rose seeds have been removed from the rose hips, rinse the seeds in a solution of purified water (any bottled water will do) with 5% bleach. This would be about two teaspoons of bleach per cup of water. Rinse the rose seeds with plain bottled water in a strainer, then soak the seeds in straight 3% peroxide for 24 hours. CAUTION: Do not mix bleach with peroxide because there could be a chemical reaction.   
Pests and diseases: Prevention is the best way to avoid pest and disease problems. Start with disease-resistant varieties, keep plants in healthy condition (well fertilized and well watered), maintain good air circulation, keep foliage dry, and remove any diseased foliage or spent flowers. For Japanese beetle grubs, use beneficial nematodes or Milky Spore (Bacillus popilliae). Rose Rx is effective against scale, spidermites and aphids. For more information, see the Pest and Disease Finder.
The Misting Method: As you get more sophisticated in your rose propagating methods you may eventually want to set up a misting bench. It can be an open-air bench or one enclosed in a greenhouse, or even a small misting box, similar to the one my husband Bob built for me. (Refer to "How We Made Our Misting Box," from Rose Ecstasy. You could choose to rig it up with a manual or an automatically-timed mister, whatever your time, money, or expertise will allow. I am fortunate to have a very handy guy for a husband, who is a good sport whenever I come up with these crazy project ideas.
After the rose seeds have soaked overnight, rinse them in a strainer and place them into the blender with at least a cup of plain purified water (making sure all seeds are covered), and turn it on for a few minutes. It usually doesn't chop up the seeds, but rather, it will clean off the pulp remaining from the rose hip, which would otherwise mold if left on the rose seed. You may see a few seeds chopped up, but those usually aren't viable anyway. Flush the rose seeds again through a strainer using fresh purified water.   
The next step when you grow roses from cuttings is to use a pencil or metal probe push down into the planting site soil to make a hole that is deep enough to plant the cutting up to about 50 percent of its overall length. Place the cutting that has been dipped into the rooting hormone into this hole. Lightly push the soil in around the cutting to finish the planting. Do the same thing for each cutting keeping them at least eight inches apart. Label each row of rose cuttings with the name of the mother rose bush it was taken from.
Place a jar over each cutting to form a sort of miniature greenhouse for each cutting. It is extremely important that the soil moisture for the cuttings does not dry out at this rooting time. The jar will help to hold humidity in, but can be a problem if it is subjected to a lot of hot afternoon sun, as it will overheat the cutting and kill it, thus the need for shielding against the exposure to the hot afternoon sun when you root roses. Watering of the planting site every other day may be required to keep the soil moist but do not create a standing water or muddy soils situation.
Hi Katherine, You may have hit the reason. One of the most common reasons for roses not blooming well is the use of high nitrogen fertilizers or the over use of them. This will result in few to no blooms or small blooms and lots of foliage. Use a well balanced food or fertilizer when feeding your roses so that all of the rose’s nutritional needs are met.
Despite their reputation for being finicky, most roses are simple to grow and easy to propagate at home. “Propagate" simply means to reproduce a plant easily from a simple cutting. Unlike seeds, which produce very different plants, rooted cuttings produce replicas of their parent. You don't have to be a trained rosarian to reproduce treasured family heirlooms or favorite garden roses.
I have successfully taken rose cuttings with both new and old wood. It is important to let the new stems sufficiently mature. The new wood is usually mature enough after the stem has just finished blooming. If you don't let the stem mature enough, then it usually becomes limp and will die before you can get it to root. I take cuttings from new rose stems in the spring right after the first bloom cycle. Then in early to late fall (in Southern California) I prefer to use more mature or old wood. When using old wood in the fall, I will remove the rose cuttings from the Mason jar, baggie, or mister, after only several weeks since it is cool enough then for them to root on their own as long as I water them daily.
Rose seeds need to go through stratification (an artificial cold spell) for 10 to 12 weeks before they will sprout. This, combined with a germination success rate of 20-30% makes propagation by seed an unattractive prospect. on by seed an unattractive prospect. If you still want to try it, find a good source of information that will guide you through the process.
I received some seeds as birthday present, the seller included a bonus packet of rose seeds. There’s no indication if they’ve been stratified. If I stratify them now, it will be July when they’re ready to plant. In this region (I’m ~50 miles north of Portland, Oregon)it might be mild or very hot. I’ve read that rose seed won’t sprout if it’s too hot – how well do rose seeds keep? Will they still be viable next Spring, or should i take a chance on the weather and start them now?
×