The easiest way to begin experimenting with rose hybridizing, especially for the beginner, is to simply let some of your roses self-pollinate themselves, so they will "go to seed" and set hips. I have found that Playboy, Hurdy Gurdy, Peggy T and Fairhope are some of the easiest roses to set hips, and there are many others. Let the rose hips stay on the rose bushes at least four months before harvesting.
Allow rose hips to develop by leaving dead flowers on the plant. The flowers are typically pollinated by insects, or pollinate themselves in some varieties, so there is no need to pollinate by hand unless you are breeding specific plants together. Leave the flowers on the rose plant without cutting them. After they wither, small fruits known as rose hips will develop in their place.
Select two roses that you want to cross-pollenate. The blooms should not be too tight, perhaps about one-half to 3/4 open. Carefully peel off all the petals. The rose stamens inside should look golden yellow and fresh. With sterile tweezers or cuticle scissors, carefully remove all the stamens at the base of the rose hip, so you do not damage the pollen sacs (anthers). Place the rose stamens into separate, clean film canisters, and place the canisters in a dry place, but not in direct sunlight.
The next step when you grow roses from cuttings is to use a pencil or metal probe push down into the planting site soil to make a hole that is deep enough to plant the cutting up to about 50 percent of its overall length. Place the cutting that has been dipped into the rooting hormone into this hole. Lightly push the soil in around the cutting to finish the planting. Do the same thing for each cutting keeping them at least eight inches apart. Label each row of rose cuttings with the name of the mother rose bush it was taken from.
Water the planted rose seeds well and place them outside in direct sunlight (no need for Grow Lights). If there is still danger of frost, then you will need to place the seed trays in a protected location such as under a tree or patio. You will need to keep the rose seed trays watered and don't let them dry out. After about six weeks, or when the weather starts to warm up, the little rose seedlings will start to sprout. They will continue to sprout as long as the weather is cool, but will stop sprouting when it gets too hot.
If you order bare-root roses from a mail-order company, order early (late winter or early spring). The roses are usually shipped in the spring because bare roots when plants are fully dormant, well before they have leafed out. They’ll look like a bundle of sticks on arrival. Note that they are not dead—simply dormant. Check that the packing material is moist and keep them in a cool dark place until ready to plant.
Grow your roses indoors, alternatively. You can also raise roses in a greenhouse. You’ll need containers that are at least 9 inches (22.9 cm) wide. Spread 1 to 2 inches (2.5 to 5.1 cm) of small pebbles at the bottom of each pot to ensure good drainage and fill each with halfway with well-draining soil. Plant the roses just beyond the graft point and then water well.
Remember that light changes as the angle of the sun shifts throughout the season. If you live in the upper half of the U.S., choose a site that will offer full sun year-round. The more sun you have, the more flowers your plants will produce. In the lower half of the U.S., choose spots with a little bit of afternoon shade. This protects blossoms from the scorching sun and helps your flowers last longer.
Fertilize the roses. After they are established, roses should be fertilized a few times per growing season. Use fertilizer (either liquid or granule) in early spring, when you see the first few leaves sprout. Use it again after the first bloom, and again if there's another bloom. Stop fertilizing the roses at the end of the summer, just before Labor Day.
Cover the cutting loosely, pot and all, with a plastic bag or plastic wrap and keep the soil moist. Putting a tall stake into the pot will hold the plastic away from the leaves. If the plastic touches the leaves, they remain wet and can succumb to a fungus disease. Along the same lines, make sure the condensation can escape from the plastic or the stem will rot.