The Baggie Method: This was the first method I ever tried. Here you fill 2-inch plastic pots with potting soil, insert the rose stem halfway inside the pot, then put the pots into a one-gallon plastic zip-lock bag. You can get four 2-inch pots into each gallon bag. I didn't like this method because it caused many of the cuttings to rot since the bags tended to fold over and therefore prevented the air from circulating. The success rate of this method is not very good. It may be helpful to place a couple of small sticks inside the bag to help keep it upright and full of air.
The plant will become dormant—and you want it to stay that way; it is the natural state. After the first deep freeze, put is in a room or place (garage) with no heat and natural light (window). You can add some water occasionally but this is not intended to be “watering”; the plant is dormant and will not take it up but the soil can be lightly moist. Bring the plant back outside when it shows signs of coming back to life. Plant it, per the guidance above, when the soil warms.
Fertilize the roses. After they are established, roses should be fertilized a few times per growing season. Use fertilizer (either liquid or granule) in early spring, when you see the first few leaves sprout. Use it again after the first bloom, and again if there's another bloom. Stop fertilizing the roses at the end of the summer, just before Labor Day.
Take a sterile Q-Tip or small sable artist's brush, and dip it into the rose pollen you want to use. Then dab the pollen-coated Q-Tip or brush onto the stigma of the rose you have selected as the seed (female) parent. You could also simply use your finger to apply the pollen to the rose. Repeat this procedure after four hours, and then again after another four hours. Label the rose hip with the name of the seed parent as well as the pollen parent, i.e. Fairhope x Miss Flippins. The name that appears first is always the seed parent (the mother), and the second name is the pollen parent (the father).
Soaking the seeds is a crucial step if your seeds will germinate properly and stay clear of any diseases. You MUST not mix the bleach with the hydrogen peroxide as this results in a chemical reaction. 3% peroxide for 24 hours is just fine. This is also a good time to perform the water float test. Remove all seeds that float as they might not be viable.
I bought hybrid tea roses last year. Not long after the first blooms, we moved one because it was interfering with the sprinkler system. It looked unhappy at first, but continued to bloom throughout the season. This year, it does not have so much as one leaf, no new foliage whatsoever, however, there is still green inside the stem towards the base of the cane. Is it done for, or is there a chance it will come back in it's second rear?
A special stainless steel screen on the handle of the unit raises up when it is dry. When this happens, it throws the mercury switch which opens the solenoid valve and starts the misting cycle. When this stainless steel screen accumulates enough mist, the weight of the water drops it down again, shutting off the mercury switch, closing the solenoid valve. It needs practically no care or maintenance and can be left on, unattended day and night. This control unit is a very practical instrument which will have a long lifetime of carefree maintenance. There are no clocks to adjust, and it is not affected by water conditions. It works simply on the weight of water. The major benefit of the Mist-a-Matic is to control the misting cycle according to weather conditions. Too much water promotes disease and wastes water. Too little water causes leaves to wilt and failure to root. The Mist-a-Matic distributes the correct amount of water. In hot weather, the unit will turn on more frequently as the water evaporates. In cooler weather, the unit turns on less frequently. For operation, you will need to plug the unit into an electrical outlet. You need to hook it up to a water source with misting nozzles.
Monitor the rose cuttings to ensure they’re hydrated and taking root. Keep an eye on the cuttings to make sure they’re never dried out, as well as to make sure the cuttings are taking root. You can test to see if the roots are growing by gently tugging on the cuttings. You should be able to feel a slight resistance after a week or 2, meaning the roots are growing well.