Remove the seeds from the fridge. Try to do this around the time that the seeds would normally start to germinate, such as in early spring. Make sure that the environment outside of the fridge is about 70 degrees Fahrenheit.[3] The seed will not sprout until you take them out of the fridge. Depending on the rose variety and individual seeds, the seeds could take anywhere from four to sixteen weeks to germinate. Often, 70% or more of the seeds never sprout at all.[4]


Just as with many other shrubs, roses can be grown from cuttings. It’s not a fast process – it may take a couple of years before your new plant produces flowers. But if you have a favourite rose, it can be fun to try. The cuttings need to be taken fresh from a healthy plant – don’t try to grow a new rose bush from the bunch of cut flowers you have sitting in a vase. And as roses bushes are pruned during winter, this is the most convenient time to take and pot up your rose cuttings.
The next step when you grow roses from cuttings is to use a pencil or metal probe push down into the planting site soil to make a hole that is deep enough to plant the cutting up to about 50 percent of its overall length. Place the cutting that has been dipped into the rooting hormone into this hole. Lightly push the soil in around the cutting to finish the planting. Do the same thing for each cutting keeping them at least eight inches apart. Label each row of rose cuttings with the name of the mother rose bush it was taken from.
Remove the seeds from the fridge. Try to do this around the time that the seeds would normally start to germinate, such as in early spring. Make sure that the environment outside of the fridge is about 70 degrees Fahrenheit.[3] The seed will not sprout until you take them out of the fridge. Depending on the rose variety and individual seeds, the seeds could take anywhere from four to sixteen weeks to germinate. Often, 70% or more of the seeds never sprout at all.[4]
Remove all but the top 2 leaflets on the stem, cutting just above the top set of leaves. You need to remove the excess leaves for the same reason we removed the flower in Step #2. They're taking up too much of the plant's energy. However we want the stem to continue to photosynthesize and feed itself until the new roots form, so we need to leave a couple of leaves.
Black Spot: Rose plant leaves with black spots that eventually turn yellow have black spot. This is often caused by water splashing on leaves, especially in rainy weather. Leaves may require a protective fungicide coating, which would start in the summer before leaf spots started until first frost. Thoroughly clean up debris in the fall, and prune out all diseased canes.
After the rose seeds have soaked overnight, rinse them in a strainer and place them into the blender with at least a cup of plain purified water (making sure all seeds are covered), and turn it on for a few minutes. It usually doesn't chop up the seeds, but rather, it will clean off the pulp remaining from the rose hip, which would otherwise mold if left on the rose seed. You may see a few seeds chopped up, but those usually aren't viable anyway. Flush the rose seeds again through a strainer using fresh purified water.    

A special stainless steel screen on the handle of the unit raises up when it is dry. When this happens, it throws the mercury switch which opens the solenoid valve and starts the misting cycle. When this stainless steel screen accumulates enough mist, the weight of the water drops it down again, shutting off the mercury switch, closing the solenoid valve. It needs practically no care or maintenance and can be left on, unattended day and night. This control unit is a very practical instrument which will have a long lifetime of carefree maintenance. There are no clocks to adjust, and it is not affected by water conditions. It works simply on the weight of water. The major benefit of the Mist-a-Matic is to control the misting cycle according to weather conditions. Too much water promotes disease and wastes water. Too little water causes leaves to wilt and failure to root. The Mist-a-Matic distributes the correct amount of water. In hot weather, the unit will turn on more frequently as the water evaporates. In cooler weather, the unit turns on less frequently. For operation, you will need to plug the unit into an electrical outlet. You need to hook it up to a water source with misting nozzles.
Remove the rose hips once ripe. The rose hips will start out small and green, then change color as they grow until they are completely red, orange, brown, or purple. You may pick them at this point, or wait until they are just beginning to dry out and wrinkle. Don't wait until they are fully dry and brown, as the seeds inside may have died by this point.
NOTE: During my move, I had cut several rose branches and placed them in a grocery paper bag in my garage--only to have forgotten to bring them home for a week. The branches had been in a broiling hot enclosed garage without water, and needless to say, they looked pretty dried out to a crisp. But I didn't want to just toss them out yet (these were the climbing Charisma roses), so I got an empty plastic detergent tub and completely immersed the stems for 2 weeks (no changing water). Then I stuck them into soil and hoped for the best. Well, I got about a 50% survival rate.
I have successfully taken rose cuttings with both new and old wood. It is important to let the new stems sufficiently mature. The new wood is usually mature enough after the stem has just finished blooming. If you don't let the stem mature enough, then it usually becomes limp and will die before you can get it to root. I take cuttings from new rose stems in the spring right after the first bloom cycle. Then in early to late fall (in Southern California) I prefer to use more mature or old wood. When using old wood in the fall, I will remove the rose cuttings from the Mason jar, baggie, or mister, after only several weeks since it is cool enough then for them to root on their own as long as I water them daily.
Hi Katherine, You may have hit the reason. One of the most common reasons for roses not blooming well is the use of high nitrogen fertilizers or the over use of them. This will result in few to no blooms or small blooms and lots of foliage. Use a well balanced food or fertilizer when feeding your roses so that all of the rose’s nutritional needs are met.
I received some seeds as birthday present, the seller included a bonus packet of rose seeds. There’s no indication if they’ve been stratified. If I stratify them now, it will be July when they’re ready to plant. In this region (I’m ~50 miles north of Portland, Oregon)it might be mild or very hot. I’ve read that rose seed won’t sprout if it’s too hot – how well do rose seeds keep? Will they still be viable next Spring, or should i take a chance on the weather and start them now? 
×