Remove the seeds from the fridge. Try to do this around the time that the seeds would normally start to germinate, such as in early spring. Make sure that the environment outside of the fridge is about 70 degrees Fahrenheit.[3] The seed will not sprout until you take them out of the fridge. Depending on the rose variety and individual seeds, the seeds could take anywhere from four to sixteen weeks to germinate. Often, 70% or more of the seeds never sprout at all.[4]
When pruning, be judicious. If you prune too hard in autumn, plants can be damaged beyond recovery. Instead, wait until spring, when plants begin to leaf out for the new season. (Roses are often not the earliest plants in the garden to respond to spring’s warming temperatures, so be patient.) Give the plant time to show its leaf buds then prune above that level.
Put the rose cuttings directly into water. It’s very important for the rose cuttings to stay hydrated so that they don’t dry out before you plant them. Immediately after you take the rose cuttings, put them in a cup of room temperature water until you’re ready to transfer them. Ideally, you’ll be ready to put them into the soil right after you cut the stems.[3]

Once you have had several weeks of below-freezing temperatures, cover the base of the rose with 12 inches of soil or mulch, and then cover the canes with straw, leaves, pine boughs or even foam insulation. Climbing roses can be wrapped right on their supports, or you can lay them on the ground and cover the canes with straw or brush. In severely cold climates, hybrid teas are sometimes partially dug up, laid down onto the soil, and the entire plant is then covered with more soil or mulch.
To start rose bush from cuttings, once the rose cuttings have been taken and brought to the planting site, take out a single cutting and remove the lower leaves only. Make a small slit with a sharp knife on one or two sides of the lower portion of the cutting, not a deep cut but just enough to penetrate the outer layer of the cutting. Dip the lower portion of the cutting into a rooting hormone powder.
Fertilize the roses. After they are established, roses should be fertilized a few times per growing season. Use fertilizer (either liquid or granule) in early spring, when you see the first few leaves sprout. Use it again after the first bloom, and again if there's another bloom. Stop fertilizing the roses at the end of the summer, just before Labor Day.[7]

Roses are usually grouped into one of two broad categories: old roses and modern roses. Old roses are those varieties discovered or developed prior to the introduction of the hybrid tea rose in 1867. But like everything else in the world of roses, when it comes to determining how a particular rose should be classified, it’s not always crystal clear.
Plant the rose bush seeds approximately ¼ inch deep in a seed-planting mix in seedling trays or your own planting trays. The trays need not be more than 3 to 4 inches deep for this use. When planting rose seeds from various rose bush hips, I use a separate tray for each different group of seeds and label the trays with that rose bushes name and planting date.
Pick a sunny spot to plant your rose cuttings. Where you place your cuttings is especially important if you’re planning on growing them outdoors. Choose a spot that’s sunny but that’s not in direct sunlight — you don’t want them to dry out. Putting the rose cuttings in a pot or container is alright as well, just make sure the container is deep and wide enough for your rose cuttings to grow.[6]

The next step when you grow roses from cuttings is to use a pencil or metal probe push down into the planting site soil to make a hole that is deep enough to plant the cutting up to about 50 percent of its overall length. Place the cutting that has been dipped into the rooting hormone into this hole. Lightly push the soil in around the cutting to finish the planting. Do the same thing for each cutting keeping them at least eight inches apart. Label each row of rose cuttings with the name of the mother rose bush it was taken from.
Fertilizer: Roses are heavy feeders, and will benefit from a steady supply of nitrogen, phosphorus and potassium. You can provide these nutrients with either liquid or granular fertilizers, at a ratio of approximately 5-8-5. In most cases, regular applications of compost, rotted manure, fish emulsion and seaweed extracts will provide roses with all the nutrients they need. These organic amendments also help to moderate pH imbalances and stimulate beneficial soil life. Other organic amendments favored by rose growers include greensand, black rock phosphate and alfalfa meal.

A gentle way to clean the rose seeds is to use a Cuisinart or other brand of blender with a dough blending attachment, which is made of plastic and does not have sharp blades. You can blend the rose seeds using this gentle dough attachment for several minutes without any damage to the seeds. Do not use a blender with sharp metal blades as damage to the rose seeds may occur.   


I planted mine in to the ground just like a normal rose bush, amending the soil with rose fertilizer and alfalfa meal. It is gorgeous, but because it's low to the ground, you should make sure to use drip irrigation or a soaker hose to water it so it doesn’t get black spots from the water splashing on the leaves. If yours is in a pot, let it go dormant in the garage or close to your home to keep the pot from freezing. Keep it watered and in the spring it should come back with more fertilizer to keep it happy.
Caring for rose bushes is important to their overall health and vigor, especially when it comes to watering. Roses require at least an inch of water weekly throughout their growing season, beginning in spring or following spring planting. While overhead watering is suitable before the onset of new growth, it is often better to water these plants at the soil line using soaker hoses or similar means. Rose bushes are very susceptible to fungal diseases, such as black spot and powdery mildew, especially when their foliage is kept too wet.
Take a sterile Q-Tip or small sable artist's brush, and dip it into the rose pollen you want to use. Then dab the pollen-coated Q-Tip or brush onto the stigma of the rose you have selected as the seed (female) parent. You could also simply use your finger to apply the pollen to the rose. Repeat this procedure after four hours, and then again after another four hours. Label the rose hip with the name of the seed parent as well as the pollen parent, i.e. Fairhope x Miss Flippins. The name that appears first is always the seed parent (the mother), and the second name is the pollen parent (the father).   
Select two roses that you want to cross-pollenate. The blooms should not be too tight, perhaps about one-half to 3/4 open. Carefully peel off all the petals. The rose stamens inside should look golden yellow and fresh. With sterile tweezers or cuticle scissors, carefully remove all the stamens at the base of the rose hip, so you do not damage the pollen sacs (anthers). Place the rose stamens into separate, clean film canisters, and place the canisters in a dry place, but not in direct sunlight.   

Just as with many other shrubs, roses can be grown from cuttings. It’s not a fast process – it may take a couple of years before your new plant produces flowers. But if you have a favourite rose, it can be fun to try. The cuttings need to be taken fresh from a healthy plant – don’t try to grow a new rose bush from the bunch of cut flowers you have sitting in a vase. And as roses bushes are pruned during winter, this is the most convenient time to take and pot up your rose cuttings.
I bought hybrid tea roses last year. Not long after the first blooms, we moved one because it was interfering with the sprinkler system. It looked unhappy at first, but continued to bloom throughout the season. This year, it does not have so much as one leaf, no new foliage whatsoever, however, there is still green inside the stem towards the base of the cane. Is it done for, or is there a chance it will come back in it's second rear?
×