A gentle way to clean the rose seeds is to use a Cuisinart or other brand of blender with a dough blending attachment, which is made of plastic and does not have sharp blades. You can blend the rose seeds using this gentle dough attachment for several minutes without any damage to the seeds. Do not use a blender with sharp metal blades as damage to the rose seeds may occur.   
The easiest way to begin experimenting with rose hybridizing, especially for the beginner, is to simply let some of your roses self-pollinate themselves, so they will "go to seed" and set hips. I have found that Playboy, Hurdy Gurdy, Peggy T and Fairhope are some of the easiest roses to set hips, and there are many others. Let the rose hips stay on the rose bushes at least four months before harvesting.   
After the rose seeds have soaked overnight, rinse them in a strainer and place them into the blender with at least a cup of plain purified water (making sure all seeds are covered), and turn it on for a few minutes. It usually doesn't chop up the seeds, but rather, it will clean off the pulp remaining from the rose hip, which would otherwise mold if left on the rose seed. You may see a few seeds chopped up, but those usually aren't viable anyway. Flush the rose seeds again through a strainer using fresh purified water.   
Rose seeds need to go through stratification (an artificial cold spell) for 10 to 12 weeks before they will sprout. This, combined with a germination success rate of 20-30% makes propagation by seed an unattractive prospect. on by seed an unattractive prospect. If you still want to try it, find a good source of information that will guide you through the process.
I too, have tried the cut rose flower method, but haven't yet been successful--perhaps because there are chemical additives that the roses have soaked up, or because there are no nodes (which are the points where new shoots grow out), or because the stems have spent much of their energy producing the flowers...BUT, perhaps if the flowers were immediately cut off and some rooting hormones applied to the bottom cut ends, that may work.

After the rose seeds have soaked overnight, rinse them in a strainer and place them into the blender with at least a cup of plain purified water (making sure all seeds are covered), and turn it on for a few minutes. It usually doesn't chop up the seeds, but rather, it will clean off the pulp remaining from the rose hip, which would otherwise mold if left on the rose seed. You may see a few seeds chopped up, but those usually aren't viable anyway. Flush the rose seeds again through a strainer using fresh purified water.   
Choose the pod -- or female -- flower that will produce the seed pod. Remove the petals. Identify the fringe of yellow pollen-producing structures called stamens that surround the central style. Cut the stamens off with small scissors so they will not accidentally pollinate that flower and so that the pollen will be available for planned pollination of other flowers.

The Baggie Method: This was the first method I ever tried. Here you fill 2-inch plastic pots with potting soil, insert the rose stem halfway inside the pot, then put the pots into a one-gallon plastic zip-lock bag. You can get four 2-inch pots into each gallon bag. I didn't like this method because it caused many of the cuttings to rot since the bags tended to fold over and therefore prevented the air from circulating. The success rate of this method is not very good. It may be helpful to place a couple of small sticks inside the bag to help keep it upright and full of air.


Chilling your seeds in a refrigerator for about six to ten weeks encourages them to germinate faster once planted. However, you must take care to avoid keeping them cold for long as they can germinate while still in the refrigerator. Place your seeds on a paper towel before moistening them. Use half purified water and half peroxide to prevent the growth of mould. You can then place them in a plastic zippered bag, mark the date and variety before placing in a refrigerator set at 1 to 3 degrees C. The paper towel should remain moist for the entire period. You can check occasionally to see if it needs remoistening. Make sure you don’t freeze the towel.
To get the best success, yor rose seed will need a period of stratification (a cold period of about 6-12 weeks). Its a good idea to time this so that it coincides with when they would naturally start to grow in spring – probably around early March, depending on weather conditions. I would look to sowing them in late November/ December and popping them outdoors or if we have a mild winter then stick them in the fridge!
When you transplant your roses, be sure to dig a much bigger hole than you think you need (for most types, the planting hole should be about 15 to 18 inches wide), and add plenty of organic matter such as compost or aged manure. This will feed your plant in the years ahead. Some old-timers recommend placing a 4-inch square of gypsum wallboard and a 16-penny nail in the hole to provide calcium and iron, both appreciated by roses.
The next step when you grow roses from cuttings is to use a pencil or metal probe push down into the planting site soil to make a hole that is deep enough to plant the cutting up to about 50 percent of its overall length. Place the cutting that has been dipped into the rooting hormone into this hole. Lightly push the soil in around the cutting to finish the planting. Do the same thing for each cutting keeping them at least eight inches apart. Label each row of rose cuttings with the name of the mother rose bush it was taken from.
Prepare a pot. Fill the small pot with potting soil. For the best results, replace a quarter of the soil with perlite, peat moss, or vermiculite, or a combination thereof. This will increase air flow and draining, giving your cutting a better opportunity to root.[2] If the soil is dry, water it and allow the excess water to drain out, so that the soil is evenly moist.
This is a fungus called black spot. Left untreated, it can cause all the leaves on your roses to turn yellow and fall off. It will also affect nearby plants, as it spreads by spores. Remove ALL INFECTED material and throw it away or burn it. Do NOT leave it on the ground as this fungus is very hardy. It can survive winter and travels very easily, even after being removed from the affected plant. Spray your plants regularly (bi-weekly) in the growing season with a good fungicide (I like the Bayer products). You can also add a little bit of dish soap and baking soda to a spray bottle with water and spray the entire plant.
×