Cathryn Chaney has worked as a gardening writer since 2002. Her horticultural experience working in the nursery industry informs her garden articles, especially those dealing with arid landscaping and drought-tolerant gardening. Chaney also writes poetry, which has appears in "Woman's World" magazine and elsewhere. Chaney graduated from the University of Arizona in 1992 with a Bachelor of Arts in English.
The next step when you grow roses from cuttings is to use a pencil or metal probe push down into the planting site soil to make a hole that is deep enough to plant the cutting up to about 50 percent of its overall length. Place the cutting that has been dipped into the rooting hormone into this hole. Lightly push the soil in around the cutting to finish the planting. Do the same thing for each cutting keeping them at least eight inches apart. Label each row of rose cuttings with the name of the mother rose bush it was taken from.
Caring for rose bushes is important to their overall health and vigor, especially when it comes to watering. Roses require at least an inch of water weekly throughout their growing season, beginning in spring or following spring planting. While overhead watering is suitable before the onset of new growth, it is often better to water these plants at the soil line using soaker hoses or similar means. Rose bushes are very susceptible to fungal diseases, such as black spot and powdery mildew, especially when their foliage is kept too wet.
Hi, I put almost 30 cuttings on water for 2 weeks until buds and little leaves came out from approximately 20 of them. I've put them on separate pots afterwards and gave them a little bit of water every day in order to maintain humid the soil but they are all drying to death! Do not know what to do! Anybody that could help? Not putting the bag as I have them inside with a room temperature around 73,4 F.
The Misting Method: As you get more sophisticated in your rose propagating methods you may eventually want to set up a misting bench. It can be an open-air bench or one enclosed in a greenhouse, or even a small misting box, similar to the one my husband Bob built for me. (Refer to "How We Made Our Misting Box," from Rose Ecstasy. You could choose to rig it up with a manual or an automatically-timed mister, whatever your time, money, or expertise will allow. I am fortunate to have a very handy guy for a husband, who is a good sport whenever I come up with these crazy project ideas.
Prepare a large hole. You'll need one for each rose bush you're planting. Use a garden spade or shovel to dig a hole 18 inches (45.7 cm) wide and 18 inches (45.7 cm) deep. The measurements don't have to be exact, but a hole this wide and deep will be suitable for most roses. Mix the soil you removed from the hole with compost, and use some of it to form a small mound in the base of the hole. Add some bonemeal or rose fertilizer.
Ever wonder if you could root and grow roses from a branch of your favorite rose bush? Roses actually root rather easily. However most roses are grafted onto the rootstock of a different type of rose than the top, flowering portion, so the rose you root and grow may look nothing like the rose you started with. Grafting is done to improve strength, disease resistance, or hardiness, and even if you do get something resembling the parent rose you took your cutting from, it might not have that rose's hardiness. Rooting a rose cutting may not be hard to do, but it is something of a gamble.
Fertilize the roses. After they are established, roses should be fertilized a few times per growing season. Use fertilizer (either liquid or granule) in early spring, when you see the first few leaves sprout. Use it again after the first bloom, and again if there's another bloom. Stop fertilizing the roses at the end of the summer, just before Labor Day.[7]

Fertilize the roses. After they are established, roses should be fertilized a few times per growing season. Use fertilizer (either liquid or granule) in early spring, when you see the first few leaves sprout. Use it again after the first bloom, and again if there's another bloom. Stop fertilizing the roses at the end of the summer, just before Labor Day.[7]
Allow rose hips to develop by leaving dead flowers on the plant. The flowers are typically pollinated by insects, or pollinate themselves in some varieties, so there is no need to pollinate by hand unless you are breeding specific plants together. Leave the flowers on the rose plant without cutting them. After they wither, small fruits known as rose hips will develop in their place.
Fertilize the roses. After they are established, roses should be fertilized a few times per growing season. Use fertilizer (either liquid or granule) in early spring, when you see the first few leaves sprout. Use it again after the first bloom, and again if there's another bloom. Stop fertilizing the roses at the end of the summer, just before Labor Day.[7]

Grow your roses indoors, alternatively. You can also raise roses in a greenhouse. You’ll need containers that are at least 9 inches (22.9 cm) wide. Spread 1 to 2 inches (2.5 to 5.1 cm) of small pebbles at the bottom of each pot to ensure good drainage and fill each with halfway with well-draining soil. Plant the roses just beyond the graft point and then water well.[5]


Fertilizer: Roses are heavy feeders, and will benefit from a steady supply of nitrogen, phosphorus and potassium. You can provide these nutrients with either liquid or granular fertilizers, at a ratio of approximately 5-8-5. In most cases, regular applications of compost, rotted manure, fish emulsion and seaweed extracts will provide roses with all the nutrients they need. These organic amendments also help to moderate pH imbalances and stimulate beneficial soil life. Other organic amendments favored by rose growers include greensand, black rock phosphate and alfalfa meal.
A special stainless steel screen on the handle of the unit raises up when it is dry. When this happens, it throws the mercury switch which opens the solenoid valve and starts the misting cycle. When this stainless steel screen accumulates enough mist, the weight of the water drops it down again, shutting off the mercury switch, closing the solenoid valve. It needs practically no care or maintenance and can be left on, unattended day and night. This control unit is a very practical instrument which will have a long lifetime of carefree maintenance. There are no clocks to adjust, and it is not affected by water conditions. It works simply on the weight of water. The major benefit of the Mist-a-Matic is to control the misting cycle according to weather conditions. Too much water promotes disease and wastes water. Too little water causes leaves to wilt and failure to root. The Mist-a-Matic distributes the correct amount of water. In hot weather, the unit will turn on more frequently as the water evaporates. In cooler weather, the unit turns on less frequently. For operation, you will need to plug the unit into an electrical outlet. You need to hook it up to a water source with misting nozzles.
Pests and diseases: Prevention is the best way to avoid pest and disease problems. Start with disease-resistant varieties, keep plants in healthy condition (well fertilized and well watered), maintain good air circulation, keep foliage dry, and remove any diseased foliage or spent flowers. For Japanese beetle grubs, use beneficial nematodes or Milky Spore (Bacillus popilliae). Rose Rx is effective against scale, spidermites and aphids. For more information, see the Pest and Disease Finder.
×