After the rose seeds have soaked overnight, rinse them in a strainer and place them into the blender with at least a cup of plain purified water (making sure all seeds are covered), and turn it on for a few minutes. It usually doesn't chop up the seeds, but rather, it will clean off the pulp remaining from the rose hip, which would otherwise mold if left on the rose seed. You may see a few seeds chopped up, but those usually aren't viable anyway. Flush the rose seeds again through a strainer using fresh purified water.
Some people don't bother to take the time to do this, but others do. While the rose seeds are soaking, you will see that some sink to the bottom and some float on the top. The seeds that float are sometimes not viable, so you might want to throw them away. The rose seeds that sink are said to be the good ones, and are the ones to plant. There are pros and cons to this theory, and many rose hybridizers simply plant all the rose seeds that are harvested.
The next step when you grow roses from cuttings is to use a pencil or metal probe push down into the planting site soil to make a hole that is deep enough to plant the cutting up to about 50 percent of its overall length. Place the cutting that has been dipped into the rooting hormone into this hole. Lightly push the soil in around the cutting to finish the planting. Do the same thing for each cutting keeping them at least eight inches apart. Label each row of rose cuttings with the name of the mother rose bush it was taken from.
Pests and diseases: Prevention is the best way to avoid pest and disease problems. Start with disease-resistant varieties, keep plants in healthy condition (well fertilized and well watered), maintain good air circulation, keep foliage dry, and remove any diseased foliage or spent flowers. For Japanese beetle grubs, use beneficial nematodes or Milky Spore (Bacillus popilliae). Rose Rx is effective against scale, spidermites and aphids. For more information, see the Pest and Disease Finder.
The ripened rose hip is then placed on a clean cutting board and cut in half to remove the seeds. Place the seeds in a clean container. Add some diluted bleach to kill off any bacteria and fungus spores. You can make the bleach by mixing drinking water with two teaspoons of household bleach. Stir the seeds well before rinsing them and using bottled water to remove all the bleach. To further clean and disinfect the seeds, put them in the container and add some hydrogen peroxide. The seeds can be soaked for up to 24 hours before rinsing them with clean water to clear all the hydrogen peroxide.
Hi this is my first year growing roses and I have 2. One is a knockout yellow rose bush and it is doing great and is absolutely beautiful. My other rose bush is a Chicago hope hybrid tea rose and just keeps getting worse and worse. I believe it has blackspot, leaves get dark spots that get bigger until they cover whole leaf and gets on the leaves all around it if I don't clip them off as soon as I start seeing the spots. I am using a sulfur based spray on both plants every 7 days and feed it MG for roses (1gallon each plant) every 7 days. It starts to look better then bad again, it's done this all spring/summer. I've had a few blooms which are beautiful but it keeps getting to be less blooms and a lot smaller than when I first purchased it. It'll be winter soon and I'm wondering if there's a way to fix it that I'm not doing? Would it be better to leave the sickly rose in the ground and mulch or dig it up/pot it and bring inside for the winter? I'd appreciate any help I'd really like it to make it but there's only couple stems left alive on it and they are pretty short.
Grow your roses indoors, alternatively. You can also raise roses in a greenhouse. You’ll need containers that are at least 9 inches (22.9 cm) wide. Spread 1 to 2 inches (2.5 to 5.1 cm) of small pebbles at the bottom of each pot to ensure good drainage and fill each with halfway with well-draining soil. Plant the roses just beyond the graft point and then water well.
Select two roses that you want to cross-pollenate. The blooms should not be too tight, perhaps about one-half to 3/4 open. Carefully peel off all the petals. The rose stamens inside should look golden yellow and fresh. With sterile tweezers or cuticle scissors, carefully remove all the stamens at the base of the rose hip, so you do not damage the pollen sacs (anthers). Place the rose stamens into separate, clean film canisters, and place the canisters in a dry place, but not in direct sunlight.
The Misting Method: As you get more sophisticated in your rose propagating methods you may eventually want to set up a misting bench. It can be an open-air bench or one enclosed in a greenhouse, or even a small misting box, similar to the one my husband Bob built for me. (Refer to "How We Made Our Misting Box," from Rose Ecstasy. You could choose to rig it up with a manual or an automatically-timed mister, whatever your time, money, or expertise will allow. I am fortunate to have a very handy guy for a husband, who is a good sport whenever I come up with these crazy project ideas.
Prepare a large hole. You'll need one for each rose bush you're planting. Use a garden spade or shovel to dig a hole 18 inches (45.7 cm) wide and 18 inches (45.7 cm) deep. The measurements don't have to be exact, but a hole this wide and deep will be suitable for most roses. Mix the soil you removed from the hole with compost, and use some of it to form a small mound in the base of the hole. Add some bonemeal or rose fertilizer.
Hi Katherine, You may have hit the reason. One of the most common reasons for roses not blooming well is the use of high nitrogen fertilizers or the over use of them. This will result in few to no blooms or small blooms and lots of foliage. Use a well balanced food or fertilizer when feeding your roses so that all of the rose’s nutritional needs are met.
Cover the cutting loosely, pot and all, with a plastic bag or plastic wrap and keep the soil moist. Putting a tall stake into the pot will hold the plastic away from the leaves. If the plastic touches the leaves, they remain wet and can succumb to a fungus disease. Along the same lines, make sure the condensation can escape from the plastic or the stem will rot.