One way to stratify the rose seeds is to place the cleaned seeds on a paper towel (a heavyweight brand such as Bounty). Then moisten the paper towel with a solution of half & half purified water and peroxide (to help prevent mold). Fold the paper towel closed, encasing all the rose seeds in the moistened paper towel. Then place the towel full of seeds into a plastic zippered bag. Mark the seed variety and date on the outside of the plastic bag with a permanent marker, and then place the bag into the refrigerator set at about 34-38 degrees. Never freeze the seeds, and do not let them dry out. The moistened paper towel should remain moist in the closed plastic bag for many weeks.   
The rose seeds can be planted right away if you have harvested them as late as November, December or January (in Southern California) or early spring after danger of frosts in your area. Place the rose seeds about one-half inch deep in a very light mixture of 50% sterile potting soil and 50% vermiculite. Some rose hybridizers use Sunshine Mix #4. You can use small pots or shallow trays to plant your seeds, whatever works for the space you have, as long as they have good drainage. Nursery flats work well for this. Lightly dust the rose seeds with RooTone or Captan before covering with soil. And then dust the top of the soil again, which will hopefully help to prevent damp-off (a disease which kills young rose seedlings). Amateur rose hybridizers concerned with toxic chemicals may want to periodically spray the seed tray with diluted peroxide and water instead of the more toxic Captan.   
Prepare a large hole. You'll need one for each rose bush you're planting. Use a garden spade or shovel to dig a hole 18 inches (45.7 cm) wide and 18 inches (45.7 cm) deep. The measurements don't have to be exact, but a hole this wide and deep will be suitable for most roses. Mix the soil you removed from the hole with compost, and use some of it to form a small mound in the base of the hole. Add some bonemeal or rose fertilizer.
After the rose seeds have soaked overnight, rinse them in a strainer and place them into the blender with at least a cup of plain purified water (making sure all seeds are covered), and turn it on for a few minutes. It usually doesn't chop up the seeds, but rather, it will clean off the pulp remaining from the rose hip, which would otherwise mold if left on the rose seed. You may see a few seeds chopped up, but those usually aren't viable anyway. Flush the rose seeds again through a strainer using fresh purified water.   
Roses are flowering perennial plants prized for their beautiful flowers, which are made up of delicate and layered petals. One of the best ways to propagate new roses is to take a cutting from an existing plant and grow it into a whole new rose bush. When you grow roses from a cutting, you cut a stem from a healthy plant and root it in a growing medium so it grows into an independent plant of its own. However, you can also propagate roses by dividing an existing plant, but this requires a little more effort than with cuttings. To propagate by division, you have to dig up an entire rose bush, cut the root system in half, and replant the two halves as separate bushes.
A special stainless steel screen on the handle of the unit raises up when it is dry. When this happens, it throws the mercury switch which opens the solenoid valve and starts the misting cycle. When this stainless steel screen accumulates enough mist, the weight of the water drops it down again, shutting off the mercury switch, closing the solenoid valve. It needs practically no care or maintenance and can be left on, unattended day and night. This control unit is a very practical instrument which will have a long lifetime of carefree maintenance. There are no clocks to adjust, and it is not affected by water conditions. It works simply on the weight of water. The major benefit of the Mist-a-Matic is to control the misting cycle according to weather conditions. Too much water promotes disease and wastes water. Too little water causes leaves to wilt and failure to root. The Mist-a-Matic distributes the correct amount of water. In hot weather, the unit will turn on more frequently as the water evaporates. In cooler weather, the unit turns on less frequently. For operation, you will need to plug the unit into an electrical outlet. You need to hook it up to a water source with misting nozzles.
After the rose seeds have soaked overnight, rinse them in a strainer and place them into the blender with at least a cup of plain purified water (making sure all seeds are covered), and turn it on for a few minutes. It usually doesn't chop up the seeds, but rather, it will clean off the pulp remaining from the rose hip, which would otherwise mold if left on the rose seed. You may see a few seeds chopped up, but those usually aren't viable anyway. Flush the rose seeds again through a strainer using fresh purified water.   
Black Spot: Rose plant leaves with black spots that eventually turn yellow have black spot. This is often caused by water splashing on leaves, especially in rainy weather. Leaves may require a protective fungicide coating, which would start in the summer before leaf spots started until first frost. Thoroughly clean up debris in the fall, and prune out all diseased canes.
Hybrid teas and floribundas usually grow no more than 2 to 3 feet high. Their form is coarse, and hardly very appealing, but they do have the ability to produce an abundance of flowers throughout the growing season. The hybrid tea has large, single blooms on long, stiff stems, whereas the floribunda has slightly smaller clusters of blooms on stems that are not as stiff.
×