Plant the rose cuttings at any point throughout the year. Some people like to plant them during the cool months, while others wait until the early summer. Rose cuttings should be able to grow during any season. However, keep in mind that they'll need to be constantly watered, so if you plant them during the summer or live in a hot climate, they're going to dry out faster. For this reason, the rainy season might be your best option.
After the rose seeds have soaked overnight, rinse them in a strainer and place them into the blender with at least a cup of plain purified water (making sure all seeds are covered), and turn it on for a few minutes. It usually doesn't chop up the seeds, but rather, it will clean off the pulp remaining from the rose hip, which would otherwise mold if left on the rose seed. You may see a few seeds chopped up, but those usually aren't viable anyway. Flush the rose seeds again through a strainer using fresh purified water.   
Cover the cutting loosely, pot and all, with a plastic bag or plastic wrap and keep the soil moist. Putting a tall stake into the pot will hold the plastic away from the leaves. If the plastic touches the leaves, they remain wet and can succumb to a fungus disease. Along the same lines, make sure the condensation can escape from the plastic or the stem will rot.
Pick a sunny spot to plant your rose cuttings. Where you place your cuttings is especially important if you’re planning on growing them outdoors. Choose a spot that’s sunny but that’s not in direct sunlight — you don’t want them to dry out. Putting the rose cuttings in a pot or container is alright as well, just make sure the container is deep and wide enough for your rose cuttings to grow.[6]

Cover the stem with plastic or a mason jar. To cover the stem with plastic, insert two eight-inch (20-cm) sticks or wires into the soil on either side of the stem to prop up the plastic. Cover the pot and stem with a clear plastic bag, and affix the bag to the pot with an elastic or twine. With a mason jar, simply place a large mason jar over the stem.
Hi, I put almost 30 cuttings on water for 2 weeks until buds and little leaves came out from approximately 20 of them. I've put them on separate pots afterwards and gave them a little bit of water every day in order to maintain humid the soil but they are all drying to death! Do not know what to do! Anybody that could help? Not putting the bag as I have them inside with a room temperature around 73,4 F.
The Baggie Method: This was the first method I ever tried. Here you fill 2-inch plastic pots with potting soil, insert the rose stem halfway inside the pot, then put the pots into a one-gallon plastic zip-lock bag. You can get four 2-inch pots into each gallon bag. I didn't like this method because it caused many of the cuttings to rot since the bags tended to fold over and therefore prevented the air from circulating. The success rate of this method is not very good. It may be helpful to place a couple of small sticks inside the bag to help keep it upright and full of air.
I bought hybrid tea roses last year. Not long after the first blooms, we moved one because it was interfering with the sprinkler system. It looked unhappy at first, but continued to bloom throughout the season. This year, it does not have so much as one leaf, no new foliage whatsoever, however, there is still green inside the stem towards the base of the cane. Is it done for, or is there a chance it will come back in it's second rear?

Please keep in mind that many rose bushes are grafted rose bushes. This means that the bottom part is a hardier rootstock that will withstand cold and heat better than the top and more desired part of the rose bush. Starting a rose bush from cuttings places the new rose bush on its own roots, so it may not be as hardy in cold climates or in extreme heat conditions climates. Being on its own root system can cause the new rose bush to be far less hardy than its mother rose bush.
One way to stratify the rose seeds is to place the cleaned seeds on a paper towel (a heavyweight brand such as Bounty). Then moisten the paper towel with a solution of half & half purified water and peroxide (to help prevent mold). Fold the paper towel closed, encasing all the rose seeds in the moistened paper towel. Then place the towel full of seeds into a plastic zippered bag. Mark the seed variety and date on the outside of the plastic bag with a permanent marker, and then place the bag into the refrigerator set at about 34-38 degrees. Never freeze the seeds, and do not let them dry out. The moistened paper towel should remain moist in the closed plastic bag for many weeks.   
The Misting Method: As you get more sophisticated in your rose propagating methods you may eventually want to set up a misting bench. It can be an open-air bench or one enclosed in a greenhouse, or even a small misting box, similar to the one my husband Bob built for me. (Refer to "How We Made Our Misting Box," from Rose Ecstasy. You could choose to rig it up with a manual or an automatically-timed mister, whatever your time, money, or expertise will allow. I am fortunate to have a very handy guy for a husband, who is a good sport whenever I come up with these crazy project ideas.
Hi, I put almost 30 cuttings on water for 2 weeks until buds and little leaves came out from approximately 20 of them. I've put them on separate pots afterwards and gave them a little bit of water every day in order to maintain humid the soil but they are all drying to death! Do not know what to do! Anybody that could help? Not putting the bag as I have them inside with a room temperature around 73,4 F.
I have successfully taken rose cuttings with both new and old wood. It is important to let the new stems sufficiently mature. The new wood is usually mature enough after the stem has just finished blooming. If you don't let the stem mature enough, then it usually becomes limp and will die before you can get it to root. I take cuttings from new rose stems in the spring right after the first bloom cycle. Then in early to late fall (in Southern California) I prefer to use more mature or old wood. When using old wood in the fall, I will remove the rose cuttings from the Mason jar, baggie, or mister, after only several weeks since it is cool enough then for them to root on their own as long as I water them daily.
Black Spot: Rose plant leaves with black spots that eventually turn yellow have black spot. This is often caused by water splashing on leaves, especially in rainy weather. Leaves may require a protective fungicide coating, which would start in the summer before leaf spots started until first frost. Thoroughly clean up debris in the fall, and prune out all diseased canes.
So grandma had the right idea in the first place, and she really did know what she was doing. It has always been fun to start roses from cuttings. Some people get their kicks by going "rose rustling" in the deserted cemeteries of old and forgotten mining towns. Others just take a twig from their favorite rose and stick it into the ground in their backyard. There is nothing complicated nor scientific about taking cuttings of roses and rooting them to "start" a new plant. There are various ways of taking rose cuttings, so let's tell you how.
Be aware of your variety’s needs. Rose care will depend a lot on the variety you’re raising. Some roses like William Baffin and Lady Hillingdon climbing roses are more drought tolerant, for example, while others need more water. Some varieties can withstand less sunlight than others. Rose varieties should also be pruned differently depending on the variety and your climate area.
This is a fungus called black spot. Left untreated, it can cause all the leaves on your roses to turn yellow and fall off. It will also affect nearby plants, as it spreads by spores. Remove ALL INFECTED material and throw it away or burn it. Do NOT leave it on the ground as this fungus is very hardy. It can survive winter and travels very easily, even after being removed from the affected plant. Spray your plants regularly (bi-weekly) in the growing season with a good fungicide (I like the Bayer products). You can also add a little bit of dish soap and baking soda to a spray bottle with water and spray the entire plant.
×