To start rose bush from cuttings, once the rose cuttings have been taken and brought to the planting site, take out a single cutting and remove the lower leaves only. Make a small slit with a sharp knife on one or two sides of the lower portion of the cutting, not a deep cut but just enough to penetrate the outer layer of the cutting. Dip the lower portion of the cutting into a rooting hormone powder.

The ripened rose hip is then placed on a clean cutting board and cut in half to remove the seeds. Place the seeds in a clean container. Add some diluted bleach to kill off any bacteria and fungus spores. You can make the bleach by mixing drinking water with two teaspoons of household bleach. Stir the seeds well before rinsing them and using bottled water to remove all the bleach. To further clean and disinfect the seeds, put them in the container and add some hydrogen peroxide. The seeds can be soaked for up to 24 hours before rinsing them with clean water to clear all the hydrogen peroxide.

Rose seeds need to go through stratification (an artificial cold spell) for 10 to 12 weeks before they will sprout. This, combined with a germination success rate of 20-30% makes propagation by seed an unattractive prospect. on by seed an unattractive prospect. If you still want to try it, find a good source of information that will guide you through the process.

Some roses root easier than others — old-fashioned heirloom types often root better than modern hybrids — but don't let that keep you from trying your hand at replicating garden favorites and sharing your love of roses and gardening with family and friends. RootBoost™ and GardenTech® brands are here to help you learn and succeed in all your gardening projects, so you can experience all the joys of gardening.
I too, have tried the cut rose flower method, but haven't yet been successful--perhaps because there are chemical additives that the roses have soaked up, or because there are no nodes (which are the points where new shoots grow out), or because the stems have spent much of their energy producing the flowers...BUT, perhaps if the flowers were immediately cut off and some rooting hormones applied to the bottom cut ends, that may work.
The rose seeds can be planted right away if you have harvested them as late as November, December or January (in Southern California) or early spring after danger of frosts in your area. Place the rose seeds about one-half inch deep in a very light mixture of 50% sterile potting soil and 50% vermiculite. Some rose hybridizers use Sunshine Mix #4. You can use small pots or shallow trays to plant your seeds, whatever works for the space you have, as long as they have good drainage. Nursery flats work well for this. Lightly dust the rose seeds with RooTone or Captan before covering with soil. And then dust the top of the soil again, which will hopefully help to prevent damp-off (a disease which kills young rose seedlings). Amateur rose hybridizers concerned with toxic chemicals may want to periodically spray the seed tray with diluted peroxide and water instead of the more toxic Captan.   
A special stainless steel screen on the handle of the unit raises up when it is dry. When this happens, it throws the mercury switch which opens the solenoid valve and starts the misting cycle. When this stainless steel screen accumulates enough mist, the weight of the water drops it down again, shutting off the mercury switch, closing the solenoid valve. It needs practically no care or maintenance and can be left on, unattended day and night. This control unit is a very practical instrument which will have a long lifetime of carefree maintenance. There are no clocks to adjust, and it is not affected by water conditions. It works simply on the weight of water. The major benefit of the Mist-a-Matic is to control the misting cycle according to weather conditions. Too much water promotes disease and wastes water. Too little water causes leaves to wilt and failure to root. The Mist-a-Matic distributes the correct amount of water. In hot weather, the unit will turn on more frequently as the water evaporates. In cooler weather, the unit turns on less frequently. For operation, you will need to plug the unit into an electrical outlet. You need to hook it up to a water source with misting nozzles.
Cover the stem with plastic or a mason jar. To cover the stem with plastic, insert two eight-inch (20-cm) sticks or wires into the soil on either side of the stem to prop up the plastic. Cover the pot and stem with a clear plastic bag, and affix the bag to the pot with an elastic or twine. With a mason jar, simply place a large mason jar over the stem.
Water: Roses require more water than most other landscape plantings, especially during the first year as the plant is getting its roots established. The best way to water your roses is with drip irrigation. It concentrates the water at the root zone where it is needed, and keeps the foliage dry to minimize disease problems. A good, thick layer of organic mulch will help conserve moisture, reduce weeds, and encourage healthy root growth. As the mulch breaks down, it will also add organic matter to the soil.
Pests and diseases: Prevention is the best way to avoid pest and disease problems. Start with disease-resistant varieties, keep plants in healthy condition (well fertilized and well watered), maintain good air circulation, keep foliage dry, and remove any diseased foliage or spent flowers. For Japanese beetle grubs, use beneficial nematodes or Milky Spore (Bacillus popilliae). Rose Rx is effective against scale, spidermites and aphids. For more information, see the Pest and Disease Finder.
×